| Name/Meaning | Offset | Type | Size (bytes) | Remark | |
|---|---|---|---|---|---|
| AFV Front | 0xffffffffffffffea | -22 | Value | 2 | Adaptive fuel value front cylinder |
| Idle Air Control Average Position | 0xffffffffffffffed | -19 | Value | 1 | Average IAC position when PID control is active |
| Active Intake Actuations | 0xffffffffffffffee | -18 | Value | 2 | Count of Active Intake actuations since cleared |
| AMC Key-On Status | 0xfffffffffffffff6 | -10 | Bits | 1 | AMC status when ignition is switched on |
| Baro Pressure Sensor Stored Value | 0xfffffffffffffff8 | -8 | Value | 1 | Stored barometric sensor reading |
| Stored Error Byte 0 | 0xfffffffffffffff9 | -7 | Bits | 1 | Stored (historic) trouble codes, byte 0 |
| Stored Error Byte 1 | 0xfffffffffffffffa | -6 | Bits | 1 | Stored (historic) trouble codes, byte 1 |
| Stored Error Byte 2 | 0xfffffffffffffffb | -5 | Bits | 1 | Stored (historic) trouble codes, byte 2 |
| Stored Error Byte 3 | 0xfffffffffffffffc | -4 | Bits | 1 | Stored (historic) trouble codes, byte 3 |
| Stored Error Byte 4 | 0xfffffffffffffffd | -3 | Bits | 1 | Stored (historic) trouble codes, byte 4 |
| Stored Error Byte 5 | 0xfffffffffffffffe | -2 | Bits | 1 | Stored (historic) trouble codes, byte 5 |
| Stored Error Byte 6 | 0xffffffffffffffff | -1 | Bits | 1 | Stored (historic) trouble codes, byte 6 |
| Stored Error Byte 7 | 0x0000 | 0 | Bits | 1 | Stored (historic) trouble codes, byte 7 |
| Stored Error Byte 8 | 0x0001 | 1 | Bits | 1 | Stored (historic) trouble codes, byte 8 |
| Stored Error Byte 9 | 0x0002 | 2 | Bits | 1 | Stored (historic) trouble codes, byte 9 |
| Stored Error Byte 10 | 0x0003 | 3 | Bits | 1 | Stored (historic) trouble codes, byte 10 |
| Number of Rides since Error Set | 0x0004 | 4 | Value | 1 | Number of rides since a trouble code was set |
| Calibration ID | 0x0005 | 5 | Value | 1 | Country specific calibration identifier |
| AFV Rear | 0x0006 | 6 | Value | 2 | Adaptive fuel value rear cylinder |
| System Configuration | 0x0008 | 8 | Bits | 1 | Global ECM setup |
| Layout Revision | 0x0009 | 9 | Value | 1 | Cal Structure Revision read only) |
| Engine Running RPM Hysteresis High Value | 0x000e | 14 | Value | 2 | Upper engine running threshold |
| Engine Running RPM Hysteresis Low Value | 0x0010 | 16 | Value | 2 | Lower engine running threshold |
| Throttle Position Sensor Reset Voltage | 0x0012 | 18 | Value | 2 | TPS voltage with a fully closed throttle, written on a TPS reset |
| Throttle Position Sensor Voltage Range | 0x0014 | 20 | Value | 2 | TPS voltage difference from fully closed to WOT |
| Throttle Position Sensor Degrees Range | 0x0016 | 22 | Value | 2 | TPS degrees difference from fully closed to WOT |
| Throttle Position Sensor Moving Average Fraction | 0x0018 | 24 | Value | 1 | TPS fraction used to detect TP changes |
| Vehicle Series Calibration ID | 0x0020 | 32 | Value | 1 | |
| Vehicle Series Calibration ID | 0x0020 | 32 | Value | 1 | |
| Vehicle Market Calibration ID | 0x0021 | 33 | Value | 1 | |
| Vehicle Market Calibration ID | 0x0021 | 33 | Value | 1 | |
| Vehicle Calibration Version | 0x0022 | 34 | Value | 1 | |
| Vehicle Calibration Version | 0x0022 | 34 | Value | 1 | |
| Calibration String | 0x0024 | 36 | String | 8 | Country version identifier |
| O2 Sensor Rich Voltage | 0x002e | 46 | Value | 1 | O2 sensor voltage indicating a rich mixture |
| O2 Sensor Lean Voltage | 0x002f | 47 | Value | 1 | O2 sensor voltage indicating a lean mixture |
| Closed Loop Feature Minimum RPM | 0x0030 | 48 | Value | 1 | Minimum RPM to activate O2 sensor |
| Closed Loop Feature Minimum Throttle | 0x0031 | 49 | Value | 1 | Minimum throttle to activate O2 sensor |
| O2 Sensor Activation Time | 0x0032 | 50 | Value | 1 | O2 sensor activation delay |
| O2 Sensor Deactivation Time | 0x0033 | 51 | Value | 1 | O2 sensor deactivation delay |
| Startup Fuel Pulsewidth | 0x0034 | 52 | Table | 6 | Starting fuel pulse length |
| Pre Sync Fuel Maximum Engine Temperature | 0x003a | 58 | Value | 1 | Max engine temp for pre-sync fuel pulses |
| Post Sync Fuel Maximum Engine Temperature | 0x003b | 59 | Value | 1 | Max engine temp for post-sync fuel pulses |
| Fuel Pump Duty Cycle Table | 0x003c | 60 | Table | 6 | Fuel pump duty cycle table |
| Fuel Pump Frequency | 0x0042 | 66 | Value | 1 | Fuel pump PWM frequency |
| AD-Converter Input Select | 0x0043 | 67 | Value | 1 | Analog-digital conversion input |
| MAP Sensor Front Reading Position | 0x0044 | 68 | Value | 1 | Crankshaft position to read front MAP sensor |
| MAP Sensor Rear Reading Position | 0x0045 | 69 | Value | 1 | Crankshaft position to read rear MAP sensor |
| TPS-MAP Load Configuration | 0x0046 | 70 | Bits | 1 | Throttle Map Load Configuration |
| TPS-MAP Load Maximum RPM | 0x0047 | 71 | Value | 1 | Maximum RPM for combined TPS/MAP TPS above) |
| Live Log Configuration | 0x0048 | 72 | Bits | 1 | Live Log Configuration |
| Global Fuel Correction | 0x004a | 74 | Value | 1 | Global fuel correction factor, applied to all map regions |
| Acceleration Enrichment Configuration | 0x004b | 75 | Bits | 1 | Acceleration Enrichment Configuration |
| Acceleration Enrichment Front Pulse Start | 0x004d | 77 | Value | 1 | Camshaft or crankshaft position to start late acceleration pulse for the front cylinder |
| Acceleration Enrichment Rear Pulse Start | 0x004e | 78 | Value | 1 | Camshaft or crankshaft position to start late acceleration pulse for the rear cylinder |
| Light Acceleration Condition | 0x004f | 79 | Value | 1 | TPS change indicating a light accel. condition |
| Full Acceleration Condition | 0x0050 | 80 | Value | 1 | Change in throttle movement indicationg a full acceleration condition |
| Acceleration Enrichment Duration | 0x0051 | 81 | Value | 1 | Full acceleration enrichment duration in engine revs |
| Acceleration Enrichment Region | 0x0052 | 82 | Table | 4 | Acceleration enrichment region |
| Acceleration Enrichment Temperature Adjustment | 0x0056 | 86 | Table | 8 | Acceleration enrichment adjustment on engine temperature |
| Acceleration Enrichment | 0x005e | 94 | Table | 8 | Acceleration enrichment |
| Deceleration Correction Region | 0x0066 | 102 | Table | 8 | Deceleration correction region |
| Deceleration Correction | 0x008e | 142 | Value | 1 | Deceleration correction |
| Deceleration Condition Hysteresis | 0x008f | 143 | Value | 1 | Deceleration condition throttle hysteresis |
| Throttle Roll-Off Condition | 0x0090 | 144 | Value | 1 | Throttle roll-off condition |
| Throttle Roll-Off Correction | 0x0091 | 145 | Value | 1 | Throttle roll-off fuel correction |
| Fuel Cut Region | 0x0092 | 146 | Table | 4 | Fuel cut region |
| Deceleration Learn Maximum RPM | 0x0096 | 150 | Value | 1 | Deceleration learn mode maximum RPM |
| Deceleration Learn Minimum RPM | 0x0097 | 151 | Value | 1 | Deceleration learn mode minimum RPM |
| Deceleration Learn Minimum Duration | 0x0098 | 152 | Value | 1 | Engine revs for deceleration learn mode |
| Deceleration Learn Minimum Readings | 0x0099 | 153 | Value | 1 | Number of consecutive rich O2 readings required |
| WOT Region | 0x009a | 154 | Table | 4 | Wide-Open Throttle definition |
| WOT Enrichment | 0x009e | 158 | Value | 2 | Default fuel correction, applied to WOT regions |
| Idle Correction | 0x00a0 | 160 | Table | 16 | Idle correction |
| Idle Maximum Engine Speed | 0x00b0 | 176 | Value | 2 | Idle region maximum RPM |
| Idle Maximum Load | 0x00b2 | 178 | Value | 1 | Idle region maximum load |
| Idle Maximum Load | 0x00b2 | 178 | Value | 1 | Idle region maximum load |
| Open Loop Enrichment Delay | 0x00b3 | 179 | Value | 1 | Time before increasing AFV |
| Startup Enrichment Temperature Axis | 0x00b4 | 180 | Axis | 4 | Startup condition temperature axis |
| Startup Enrichment | 0x00b8 | 184 | Map | 4 | Fuell correction after egine startup |
| Startup Enrichment Duration | 0x00bc | 188 | Map | 4 | Duration of startup fuel enrichment |
| Open Loop Default Correction | 0x00c0 | 192 | Value | 2 | Default fuel correction, applied to open loop regions |
| Front Cylinder Correction | 0x00c2 | 194 | Table | 8 | Front cylinder fuel enrichment on engine temperature |
| Warmup Enrichment | 0x00ca | 202 | Table | 28 | Engine temperature fuel correction |
| Hot Start Condition | 0x00e6 | 230 | Value | 2 | Engine temperature indicating a hot start condition |
| Engine Temperature Sensor Conversion Data | 0x00e8 | 232 | Table | 28 | Engine temperature senor data |
| Air Temperature Correction | 0x0104 | 260 | Table | 14 | Air Temp correction |
| Air Temperature Sensor Data | 0x0112 | 274 | Table | 28 | Air temperature sensor data |
| Battery Voltage Correction | 0x012e | 302 | Table | 12 | Battery voltage correction |
| 2nd Battery Voltage Correction | 0x013a | 314 | Table | 12 | Battery correction for showerheads |
| Barometric Pressure Sensor Reading Configuration | 0x0146 | 326 | Bits | 1 | Barometric pressure sensor access setup |
| Baro Pressure Sensor Delay | 0x0147 | 327 | Value | 1 | Delay before reading barometric pressure sensor when switching on ignition |
| Barometric Feature Region | 0x0148 | 328 | Table | 8 | Barometric feature region lower boundary |
| MAP Barometric Correction | 0x0150 | 336 | Table | 8 | Baro adjustment of MAP reads |
| Baro Pressure Sensor Moving Average Factor | 0x0158 | 344 | Value | 1 | Baro Pressure Sensor Moving Average Factor |
| Airbox Pressure Configuration | 0x0159 | 345 | Bits | 1 | Air pressure sensor configuration byte |
| Barometric Pressure Key-On Minimum Value | 0x015a | 346 | Value | 1 | Minimum valid barometric pressure sensor reading when switching on ignition |
| Barometric Pressure Key-On Maximum Value | 0x015b | 347 | Value | 1 | Maximum valid barometric pressure sensor reading when switching on ignition |
| Airbox Pressure Sensor Data | 0x015c | 348 | Table | 14 | Air Box Pressure conversion |
| Baro Correction | 0x016a | 362 | Table | 14 | Baro pressure correction |
| Vehicle Speed Correction | 0x0178 | 376 | Table | 16 | Airbox pressure correction for speed |
| Airbox Pressure Correction | 0x0188 | 392 | Table | 16 | Airbox pressure correction |
| Closed Loop Configuration | 0x0198 | 408 | Bits | 1 | Fuel closed loop setup |
| Calibration Mode Number of Readings | 0x0199 | 409 | Value | 1 | Number of O2 sensor readings required to adjust AFV |
| Closed Loop Region Upper Boundary | 0x019a | 410 | Table | 8 | Closed loop upper boundary |
| Closed Loop Region Lower Boundary | 0x01a2 | 418 | Table | 18 | Closed loop lower boundary |
| Closed Loop Upper Boundary Load Hysteresis | 0x01b4 | 436 | Value | 1 | Upper closed loop boundary hysteresis, TPP |
| Closed Loop Lower Boundary Load Hysteresis | 0x01b5 | 437 | Value | 1 | Lower closed loop boundary hysteresis, TPP |
| Closed Loop Upper Boundary RPM Hysteresis | 0x01b6 | 438 | Value | 2 | Closed loop upper boundary RPM hysteresis |
| Closed Loop Lower Boundary RPM Hysteresis | 0x01b8 | 440 | Value | 2 | Closed loop lower boundary RPM hysteresis |
| EGO Correction Maximum Value | 0x01ba | 442 | Value | 2 | Maximum closed loop EGO correction |
| EGO Correction Minimum Value | 0x01bc | 444 | Value | 2 | Minimum closed loop EGO correction |
| Closed Loop Maximum Engine Temperature | 0x01be | 446 | Value | 2 | Maximum engine temperature to activate closed loop |
| Closed Loop Minimum Engine Temperature | 0x01c0 | 448 | Value | 2 | Minimum engine temperature to activate closed loop |
| Closed Loop Lower Boundary Adjustment Value | 0x01c2 | 450 | Value | 1 | Lower closed loop region boundary adjustment value |
| Closed Loop Lower Boundary Adjustment Highest Gear | 0x01c3 | 451 | Value | 1 | Highest gear where lower closed loop region boundary is adjusted |
| AFV Maximum Value | 0x01c4 | 452 | Value | 2 | Maximum allowed AFV |
| AFV Minimum Value | 0x01c6 | 454 | Value | 2 | Minimum allowed AFV |
| AFV Increase Factor | 0x01c8 | 456 | Value | 2 | Factor applied to increase AFV |
| AFV Decrease Factor | 0x01ca | 458 | Value | 2 | Factor applied to decrease AFV |
| Calibration Mode Maximum Engine Temperature | 0x01cc | 460 | Value | 2 | Maximum engine temperature to enable calibration mode |
| Calibration Mode Minimum Engine Temperature | 0x01ce | 462 | Value | 2 | Minimum engine temperature to enable calibration mode |
| Calibration Mode Region Upper Boundary | 0x01d0 | 464 | Table | 8 | Calibration mode region upper boundary |
| Calibration Mode Region Lower Boundary | 0x01d8 | 472 | Table | 14 | Calibration mode region lower boundary |
| Altitude Adjustement Lower Boundary | 0x01e6 | 486 | Table | 6 | Altitude adjustment lower boundary |
| Altitude Adjustment Upper Boundary | 0x01ec | 492 | Table | 6 | Altitude adjustment upper boundary |
| Fuel PI Controller Low RPM Threshold | 0x01f2 | 498 | Value | 1 | PI controller low value RPM limit |
| Fuel PI Controller Low Load Threshold | 0x01f3 | 499 | Value | 1 | PI controller low value load limit |
| Fuel PI Controller High RPM Threshold | 0x01f4 | 500 | Value | 1 | PI controller high value RPM limit |
| Fuel PI Controller High Load Threshold | 0x01f5 | 501 | Value | 1 | PI controller high value load limit |
| O2 Sensor Target Voltage Array | 0x01fd | 509 | Array | 5 | O2 midpoint for idle, lo, mid and hi |
| Fuel PI Controller P-Value Table Front when Rich | 0x0202 | 514 | Array | 5 | Proportional values for the front cylinder and rich transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Front when Rich | 0x0207 | 519 | Array | 5 | Integral values for the front cylinder and rich mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Front when Lean | 0x020c | 524 | Array | 5 | Proportional values for the front cylinder and lean transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Front when Lean | 0x0211 | 529 | Array | 5 | Integral values for the front cylinder and lean mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Rear when Rich | 0x0216 | 534 | Array | 5 | Proportional values for the rear cylinder and rich transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Rear when Rich | 0x021b | 539 | Array | 5 | Integral values for the rear cylinder and rich mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Rear when Lean | 0x0220 | 544 | Array | 5 | Proportional values for the rear cylinder and lean transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Rear when Lean | 0x0225 | 549 | Array | 5 | Integral values for the rear cylinder and lean mixture (idle, low, mid, high) |
| Fuel Pulse Endpoint Table for Engine Temperature | 0x0230 | 560 | Table | 6 | Fuel pulse endpoint temperature correction |
| 2nd Fuel Puls Endpoint Temperature Correction | 0x023c | 572 | Table | 6 | Showerhead pulse end point, ET based |
| 2nd Fuel Pulse Endpoint Throttle Correction | 0x0242 | 578 | Table | 6 | Showerhead pulse end point, load based |
| Fuel Pulse Endpoint Load Axis | 0x0248 | 584 | Axis | 6 | Fuel endpoint load axis |
| Fuel Pulse Endpoint RPM Axis | 0x024e | 590 | Axis | 12 | Fuel endpoint RPM axis |
| Fuel Pulse Endpoint Table | 0x025a | 602 | Map | 36 | Fuel endpoint speed/load table |
| Table Lock Value | 0x0280 | 640 | Value | 2 | |
| AFV Storage Delay | 0x0282 | 642 | Value | 1 | Time between AFV writes to EEPROM |
| Timing Tables Configuration | 0x0283 | 643 | Bits | 1 | Timing Tables Configuration Byte |
| Global Spark Advance | 0x0285 | 645 | Value | 1 | Global spark advance adjustment |
| Timed Spark Adjust Minimum RPM | 0x0286 | 646 | Value | 2 | Minimum RPM to enable spark advance adjusting |
| Idle Spark Advance Table Front | 0x0288 | 648 | Table | 12 | Idle Spark Advance for the Front Cylinder |
| Idle Spark Advance Table | 0x0294 | 660 | Table | 12 | Idle Spark Advance |
| WOT Spark Advance Reduction | 0x02c0 | 704 | Table | 8 | WOT spark advance reduction |
| Air Temperature Spark Retard Configuration | 0x02d7 | 727 | Bits | 1 | Air Temp Retard Configuration |
| Air Temperature Spark Advance Reduction Scaling | 0x02d8 | 728 | Table | 14 | Air temp spark retard |
| VSS Input Minimum Frequency | 0x02e7 | 743 | Value | 1 | Minimum valid VSS input frequency |
| VSS Input Scaling Factor | 0x02e8 | 744 | Value | 2 | Scale factor for VSS input |
| VSS Output Scaling Factor | 0x02ea | 746 | Value | 2 | Scale factor for VSS output |
| VS-RPM Ratio VS Sampling Time | 0x02ec | 748 | Value | 1 | Time to count speed sensor pulses |
| Speed-RPM Ratio RPM Sample Duration | 0x02ed | 749 | Value | 1 | Sample period for Speed-RPM ratio |
| VSS Ratio Gearing Table | 0x02ee | 750 | Array | 6 | Gear selection |
| Spark Advance Retard Configuration | 0x0326 | 806 | Bits | 1 | Spark advance and fuel reduction configuration |
| Spark Advance Retard Minimum Engine Temperature | 0x0327 | 807 | Value | 1 | Minimum engine temperature to enable reduction |
| Spark Advance Reduction Upper RPM Boundary | 0x032e | 814 | Array | 7 | Maximum RPM to enable reduction |
| Spark Advance Reduction Lower RPM boundary | 0x0335 | 821 | Array | 7 | Minimum RPM to enable reduction |
| Spark Advance Reduction Fuel Correction | 0x033c | 828 | Array | 7 | Fuel correction during activation |
| Spark Advance Reduction | 0x0343 | 835 | Array | 7 | The spark advance reduction while noise abatement is active |
| Spark Advance Reduction Ramp-In Duration | 0x034a | 842 | Array | 7 | Spark advance reduction ramp-in duration |
| Spark Advance Reduction Hold Duration | 0x0351 | 849 | Array | 7 | Spark advance reduction hold duration |
| Spark Advance Reduction Ramp-Out Duration | 0x0358 | 856 | Array | 7 | Spark advance reduction ramp-out duration |
| Active Intake Configuration | 0x035f | 863 | Bits | 1 | Active intake controller setup |
| Active Intake Gearing | 0x0360 | 864 | Bits | 1 | Active intake gearing configuration byte |
| Active Intake Period | 0x0361 | 865 | Value | 1 | Active intake control period |
| Active Intake Ramp In Duty Cycle | 0x0362 | 866 | Value | 1 | Active intake ramp-in period duty cycle |
| Active Intake Hold Duty Cycle | 0x0363 | 867 | Value | 1 | Active intake hold period duty cycle |
| Active Intake Ramp Out Duty Cycle | 0x0364 | 868 | Value | 1 | Active intake ramp-out period duty cycle |
| Fuel and Spark Skip Configuation | 0x0385 | 901 | Bits | 1 | Fuel and Spark Skip Configuation |
| RPM Fixed Limit Cold Start Ramp | 0x0386 | 902 | Value | 1 | Temperature delta to ramp from cold RPM limits |
| Soft Limit Ignition Pattern Front | 0x0387 | 903 | Value | 1 | Front Soft Limit Fire Pattern |
| Soft Limit Ignition Pattern Rear | 0x0388 | 904 | Value | 1 | Rear Soft Limit Fire Pattern |
| Hard Limit Ignition Pattern Front | 0x0389 | 905 | Value | 1 | Front Hard Limit Fire Pattern |
| Hard Limit Ignition Pattern Rear | 0x038a | 906 | Value | 1 | Rear Hard Limit Fire Pattern |
| RPM Fixed Soft Limit Trigger for Cold Engine | 0x038b | 907 | Value | 1 | Cold engine soft RPM limit, high |
| RPM Fixed Soft Limit Recharge for Cold Engine | 0x038c | 908 | Value | 1 | Cold engine soft RPM limit, low |
| RPM Fixed Hard Limit Trigger for Cold Engine | 0x038d | 909 | Value | 1 | Cold engine hard RPM limit, high |
| RPM Fixed Hard Limit Recharge for Cold Engine | 0x038e | 910 | Value | 1 | Cold engine hard RPM limit, low |
| RPM Fixed Soft Limit Trigger | 0x038f | 911 | Value | 1 | Fixed soft limit trigger RPM |
| RPM Fixed Soft Limit Recharge | 0x0390 | 912 | Value | 1 | Fixed soft limit release RPM |
| RPM Fixed Hard Limit Trigger | 0x0391 | 913 | Value | 1 | Fixed hard limit trigger RPM |
| RPM Fixed Hard Limit Recharge | 0x0392 | 914 | Value | 1 | Fixed hard limit release RPM |
| RPM Fixed Kill Limit Trigger | 0x0393 | 915 | Value | 1 | Kill limit trigger RPM |
| RPM Fixed Kill Limit Recharge | 0x0394 | 916 | Value | 1 | Kill limit release RPM |
| RPM High Speed Hysteresis High Value | 0x0395 | 917 | Value | 1 | High speed speed-RPM-ratio hysteresis, upper value |
| RPM High Speed Hysteresis Low Value | 0x0396 | 918 | Value | 1 | High speed speed-RPM-ratio hysteresis, lower value |
| RPM High Speed Timed Limit Timer Start | 0x0397 | 919 | Value | 1 | RPM threshold to start limit timer at high speed |
| RPM High Speed Timed Limit Timer Reset | 0x0398 | 920 | Value | 1 | RPM threshold to reset limit timer at high speed |
| RPM High Speed Timed Hard Limit | 0x0399 | 921 | Value | 1 | RPM threshold to enable delayed hard limit at high speed |
| RPM High Speed Timed Soft Limit | 0x039a | 922 | Value | 1 | RPM threshold to enable delayed soft limit at high speed |
| RPM High Speed Timed Soft Limit Delay | 0x039b | 923 | Value | 1 | Soft limit delay at high speed |
| RPM High Speed Timed Hard Limit Delay | 0x039c | 924 | Value | 1 | Hard limit delay at high speed |
| RPM Low Speed Timed Limit Timer Start | 0x039d | 925 | Value | 1 | RPM threshold to start limit timer at low speed |
| RPM Low Speed Timed Limit Timer Reset | 0x039e | 926 | Value | 1 | RPM threshold to reset limit timer at low speed |
| RPM Low Speed Timed Hard Limit | 0x039f | 927 | Value | 1 | RPM threshold to enable delayed hard limit at low speed |
| RPM Low Speed Timed Soft Limit | 0x03a0 | 928 | Value | 1 | RPM threshold to enable delayed soft limit at low speed |
| RPM Low Speed Timed Soft Limit Delay | 0x03a1 | 929 | Value | 1 | Soft limit delay at low speed |
| RPM Low Speed Timed Hard Limit Delay | 0x03a2 | 930 | Value | 1 | Hard limit delay at low speed |
| Temperature Soft Limit Minimum Load | 0x03a3 | 931 | Value | 1 | Load above which soft temp limit enabled |
| Temperature Soft Limit Minimum RPM | 0x03a4 | 932 | Value | 1 | Minimum RPM to enable temperature soft limit |
| Temperature Hard Limit Minimum Load | 0x03a5 | 933 | Value | 1 | Load above which hard temp limit enabled |
| Temperature Hard Limit Minimum RPM | 0x03a6 | 934 | Value | 1 | Minimum RPM to enable temperature hard limit |
| Temperature Soft Limit Trigger | 0x03a7 | 935 | Value | 1 | Temperature threshold to trigger soft limit |
| Temperature Soft Limit Recharge | 0x03a8 | 936 | Value | 1 | Temperature threshold to recharge soft limit |
| Temperature Hard Limit Trigger | 0x03a9 | 937 | Value | 1 | Temperature trheshold to trigger hard limit |
| Temperature Hard Limit Recharge | 0x03aa | 938 | Value | 1 | Temperature threshold to recharge hard limit |
| Ignore Minimum RPM Trigger | 0x03ab | 939 | Value | 1 | Temperature threshold indicating to ignore RPM/throttle limits |
| Ignore Minimum RPM Recharge | 0x03ac | 940 | Value | 1 | Temperature threshold indicating to obey RPM/throttle limits |
| Temperature Kill Limit Trigger | 0x03ad | 941 | Value | 1 | Temperature trheshold to trigger hard limit |
| Temperature Kill Limit Recharge | 0x03ae | 942 | Value | 1 | Temperature threshold to recharge kill limit |
| Temperature Limit Engine Lamp On Value | 0x03af | 943 | Value | 1 | Temperature threshold to switch on engine lamp |
| Temperature Limit Engine Lamp Off Value | 0x03b0 | 944 | Value | 1 | Temperature threshold to switch off engine lamp |
| Soft Limit Ignition Pattern Front for Neutral or Clutch | 0x03bf | 959 | Value | 1 | Front soft limit fire pattern when in neutral or clutch disengaged |
| Soft Limit Ignition Pattern Rear for Neutral or Clutch | 0x03c0 | 960 | Value | 1 | Rear soft limit fire pattern when in neutral or clutch disengaged |
| Hard Limit Ignition Pattern Front for Neutral or Clutch | 0x03c1 | 961 | Value | 1 | Front hard limit fire pattern when in neutral or clutch disengaged |
| Hard Limit Ignition Pattern Rear for Neutral or Clutch | 0x03c2 | 962 | Value | 1 | Rear hard limit fire pattern when in neutral or clutch disengaged |
| RPM Soft Limit Trigger for Neutral or Clutch | 0x03c3 | 963 | Value | 1 | Fixed soft limit trigger RPM when in neutral or clutch disengaged |
| RPM Soft Limit Recharge for Neutral or Clutch | 0x03c4 | 964 | Value | 1 | Fixed soft limit release RPM when in neutral or clutch disengaged |
| RPM Hard Limit Trigger for Neutral or Clutch | 0x03c5 | 965 | Value | 1 | Fixed hard limit trigger RPM when in neutral or clutch disengaged |
| RPM Hard Limit Recharge for Neutral or Clutch | 0x03c6 | 966 | Value | 1 | Fixed hard limit release RPM when in neutral or clutch disengaged |
| Fan Configuration | 0x03c9 | 969 | Bits | 1 | Fan Configuration |
| Fan Key-On On Temperature | 0x03ca | 970 | Value | 1 | Temperature threshold to switch on fan |
| Fan Key-On Off Temperature | 0x03cb | 971 | Value | 1 | Temperature threshold to switch off fan |
| Fan Key-On Duty Cycle | 0x03cc | 972 | Table | 8 | Fan key-on duty cycle |
| Fan VS On Temperature Table | 0x03d4 | 980 | Table | 8 | Fan-on temperature against speed |
| Fan VS Off Temperature Table | 0x03dc | 988 | Table | 8 | Fan-off temperature against speed |
| Fan Duty Cycle Period | 0x03f4 | 1012 | Value | 1 | Cooling Fan Control Period |
| Fan Key-Off Run Delay | 0x03f5 | 1013 | Value | 1 | Key-off delay before starting fan |
| Fan Key-Off Run Duty Cycle | 0x03f6 | 1014 | Value | 1 | Fan duty cycle after key-off |
| Fan Key-Off On Temperature | 0x03f7 | 1015 | Value | 1 | Key-off temperature threshold to switch on fan |
| Fan Key-Off Off Temperature | 0x03f8 | 1016 | Value | 1 | Key-off temperature threshold to switch off fan |
| Fan Key-Off Maximum Duration | 0x03f9 | 1017 | Value | 1 | Maximum time running fan after key-off |
| Fan Key-Off Minimum Battery Voltage | 0x03fa | 1018 | Value | 1 | Minimum battery voltage to run fan after key-off |
| Fan 2 Delay | 0x03fb | 1019 | Value | 1 | Delay before switching on fan 2 after turning on fan 1 |
| Battery Key-On Voltage Moving Average Factor | 0x03fd | 1021 | Value | 1 | |
| Battery Key-Off Voltage Moving Average Factor | 0x03fe | 1022 | Value | 1 | |
| Fan Duty Cycle Map Temperature Axis | 0x0400 | 1024 | Axis | 4 | Engine temperature axis for fan duty cycle map |
| Fan Duty Cycle Map Battery Axis | 0x0404 | 1028 | Axis | 8 | Battery voltage axis for fan duty cycle map |
| Fan Duty Cycle Map | 0x040c | 1036 | Map | 16 | Fan duty cycle map for battery and engine temperature |
| Fan Key-On On Temperature Table | 0x041c | 1052 | Table | 8 | Key-on fan on temp based on battery voltage |
| Fan Key-On Off Temperature Table | 0x0424 | 1060 | Table | 8 | Key-on fan off temp based on battery voltage |
| Fan Key-Off On Temperature Table | 0x042c | 1068 | Table | 8 | Key-off fan on temp based on battery voltage |
| Fan Key-Off Off Temperature Table | 0x0434 | 1076 | Table | 8 | Key-off fan off temp based on battery voltage |
| Fan Key-Off Minimum Battery Voltage Table | 0x043c | 1084 | Table | 8 | Min bat for fuel pump and fans after key-off |
| Active Muffler Configuration | 0x044a | 1098 | Bits | 1 | Active Muffler Valve Configuration |
| Active Muffler WOT Condition Hysteresis | 0x044b | 1099 | Value | 1 | Active exhaust valve WOT condition hysteresis |
| Active Muffler Motor Minimum On Time | 0x044c | 1100 | Value | 1 | Active exhaust valve controller minimum on-time |
| Active Muffler Motor Minimum Off Time | 0x044d | 1101 | Value | 1 | Active exhaust valve controller minimum off-time |
| Active Muffler Valve Switching Points | 0x044e | 1102 | Array | 6 | Active exhaust valve switching RPMs |
| Shifter Configuration | 0x048e | 1166 | Bits | 1 | Shifter configuration |
| Shifter Input | 0x048f | 1167 | Value | 1 | Input pin for shifter feature |
| Shifter Input Activation Level | 0x0490 | 1168 | Value | 1 | Shifter feature activation voltage |
| Shifter Input Debounce Time | 0x0491 | 1169 | Value | 1 | Shifter feature debounce time |
| Shifter Input Minimum Delay | 0x0492 | 1170 | Value | 1 | Minimum wait time between shifts |
| Shifter Minimum RPM | 0x0493 | 1171 | Value | 1 | Minimum rpm to activate shifter feature |
| Shifter Interrupt Duration | 0x0495 | 1173 | Axis | 7 | Length of shift interrupt |
| Shift Light Configuration | 0x049c | 1180 | Bits | 1 | Shift Light Configuration |
| Shift Light Flashing Period | 0x049d | 1181 | Value | 1 | Shift light on time while flashing |
| Shift Light Flashing RPM Hysteresis High | 0x049e | 1182 | Array | 7 | Shift Light flashing above this speed |
| Shift Light Flashing RPM Hysteresis Low | 0x04a5 | 1189 | Array | 7 | Shift Light stops flashing below this speed |
| Shift Light On RPM Hysteresis High | 0x04ac | 1196 | Array | 7 | Shift Light on above this speed |
| Shift Light Off RPM Hysteresis Low | 0x04b3 | 1203 | Array | 7 | Shift Light off below this speed |
| Starter Interlock Configuration | 0x04ba | 1210 | Bits | 1 | Starter Interlock Configuration |
| Sidestand Interlock Signal Threshold | 0x04bb | 1211 | Value | 1 | Threshold for sidestand input |
| Starter Relay Maximum RPM Hysteresis High | 0x04bc | 1212 | Value | 1 | Max RPM for starter relay upper hysteresis |
| Starter Relay Maximum RPM Hysteresis Low | 0x04bd | 1213 | Value | 1 | Max RPM for starter relay lower hysteresis |
| Sidestand Interlock Maximum Speed | 0x04be | 1214 | Value | 1 | Sidestand interlock disabled after reaching speed |
| Sidestand Input Number of Errors | 0x04bf | 1215 | Value | 1 | Sidestand extended at high speed before failure |
| Sidestand Input Maximum Reading Allowed | 0x04c0 | 1216 | Value | 1 | Upper limit of sidestand input |
| Sidestand Input Minimum Reading Allowed | 0x04c1 | 1217 | Value | 1 | Lower limit of sidestand input |
| Idle Air Control Configuration | 0x04c2 | 1218 | Bits | 1 | Idle air control setup |
| Idle Air Control Average Maximum Value | 0x04d2 | 1234 | Value | 1 | Maximum value for idle air control moving average |
| Idle Air Control Average Minimum Value | 0x04d3 | 1235 | Value | 1 | Minimum value for idle air control moving average |
| Idle Air Control Moving Average Factor | 0x04d6 | 1238 | Value | 1 | Idle air control factor to set up moving average |
| Idle Air Control Average Maximum Engine Temperature | 0x04d7 | 1239 | Value | 1 | Maximum engine temperature for idle air control moving average |
| Idle Air Control Average Minimum Engine Temperature | 0x04d8 | 1240 | Value | 1 | Minimum engine temperature for idle air control moving average |
| Running (RPM) IAC Position Map Scale Factor | 0x04dc | 1244 | Array | 7 | Scaling Factor for Running RPM) IAC Position Map Cell Value |
| Running IAC Position Map Engine Temp. Axis | 0x04e3 | 1251 | Axis | 4 | Running IAC Position Map Engine Temp. Axis |
| Running IAC Position Map Gear Axis | 0x04e7 | 1255 | Axis | 3 | Running IAC Position Map Gear Axis |
| Running (Gear) IAC Position Map | 0x04ea | 1258 | Map | 12 | IAC Position Map for running in gear |
| Running IAC Position Map RPM Axis | 0x04f7 | 1271 | Axis | 7 | Running IAC Position Map RPM Axis |
| Running (RPM) IAC Position Map | 0x04fe | 1278 | Map | 28 | IAC Position Map for running RPM |
| Idle Air Control Key-On Position | 0x051a | 1306 | Table | 8 | IAC position for startup |
| Idle Air Control Setpoint Table | 0x0522 | 1314 | Table | 12 | Idle RPM setpoint table. |
| Idle Air Control Setpoint Map Temperature Axis | 0x052e | 1326 | Axis | 6 | Engine temperature axis for IAC setpoint map |
| Idle Air Control Setpoint Map Battery Axis | 0x0534 | 1332 | Axis | 8 | Battery voltage axis for IAC setpoint map |
| Idle Air Control Setpoint Map | 0x053c | 1340 | Map | 24 | IAC RPM setpoint map for battery voltage and engine temperature |
| Idle Air Control Startup Correction | 0x0554 | 1364 | Map | 4 | IAC RPM setpoint correction for startup |
| Idle Air Control Throttle Position Adjustment | 0x0558 | 1368 | Table | 16 | Throttle position adjustment table for IAC position |
| Idle Air Control TP Adjustment Scaling | 0x0568 | 1384 | Table | 16 | Scaling of IAC throttle position adjustment for throttle position load |
| CAN Bus Configuration | 0x0582 | 1410 | Bits | 1 | CAN bus setup |
| Global Fuel Scale Increment | 0x0584 | 1412 | Value | 1 | Incremental Fuel scale, time per unit of fuel |
| Cold Start Condition | 0x0589 | 1417 | Value | 1 | Engine temperature indicates a cold engine condition. The CAN cold flag is set and cold engine RPM limit apply. |
| Aux Power Relay Configuration | 0x05a2 | 1442 | Bits | 1 | Aux Power Relay Configuration |
| Aux Power Relay On Battery Voltage | 0x05a3 | 1443 | Value | 1 | Battery voltage above which aux relay turned on |
| Aux Power Relay Off Battery Voltage | 0x05a4 | 1444 | Value | 1 | Battery voltage below which aux relay turned off |
| Aux Power Relay Switching Delay | 0x05a5 | 1445 | Value | 1 | Delay before switching aux relay |
| Spark Plug Cleaning Configuration | 0x05a6 | 1446 | Bits | 1 | Spark Plug Cleaning Configuration |
| Spark Plug Cleaning Maximum Engine Temperature | 0x05a8 | 1448 | Value | 1 | No plug cleaning needed if TE exceeds this |
| Spark Plug Cleaning Waste Fire Maximum Engine Temperature | 0x05a9 | 1449 | Value | 1 | Terminate plug cleaning waste fires above this TE |
| Spark Plug Cleaning Engine Minimum Run Time | 0x05aa | 1450 | Value | 1 | Min time for engine run event for plug cleaning |
| Spark Plug Cleaning Number of Cold Runs | 0x05ab | 1451 | Value | 1 | Cold run events before plug cleaning needed |
| Spark Plug Key-On Cleaning Time | 0x05ad | 1453 | Value | 1 | Duration of key-on plug cleaning |
| Spark Plug Cleaning Number of Waste Fires | 0x05ae | 1454 | Value | 1 | Plug cleaning waste fires per rev |
| Fuel Pressure Control Configuration | 0x05d2 | 1490 | Bits | 1 | Fuel Pressure Control Configuration |
| Fuel Pressure Key-Off Minimum Pressure | 0x05e8 | 1512 | Table | 6 | Minimum fuel pressure when engine off |
| Fuel Pressure Setpoint for Startup | 0x05f6 | 1526 | Map | 4 | Fuel Pressure setpoint at startup |
| Fuel Pressure Setpoint for Engine Temperature | 0x05fa | 1530 | Table | 28 | Fuel pressure setpoint table for engine temperature |
| Fuel Pressure Sensor Conversion Table | 0x0616 | 1558 | Table | 28 | Fuel pressure sensor data |
| Fuel Pressure Setpoint Load Axis | 0x0632 | 1586 | Axis | 6 | Load axis for fuel pressure setpoint map |
| Fuel Pressure Setpoint RPM Axis | 0x0638 | 1592 | Axis | 12 | RPM axis for fuel pressure setpoint map |
| Fuel Pressure Setpoint | 0x0644 | 1604 | Map | 36 | Fuel pressure setpoint map for RPM and load |
| Voltage and Fuel Pressure Correction Temperature Axis | 0x0668 | 1640 | Axis | 6 | Fuel pressure axis for voltage and fuel pressure correction map |
| Voltage and Fuel Pressure Correction Battery Axis | 0x066e | 1646 | Axis | 12 | Battery axis for voltage and fuel pressure correction map |
| Voltage and Fuel Pressure Correction | 0x067a | 1658 | Map | 36 | Injector adder based on fuel pressure and battery |
| Fuel Pressure Correction | 0x069e | 1694 | Table | 8 | Fuel Pressure correction |
| Rides Required to Clear DTC | 0x06bc | 1724 | Value | 1 | Number of rides without error codes set to clear store errors |
| Throttle Position Sensor Number of Errors | 0x06bd | 1725 | Value | 1 | Number of TPS read failures before error code is set |
| Throttle Position Sensor Highest Reading Allowed | 0x06be | 1726 | Value | 2 | Maximum TPS reading |
| Throttle Position Sensor Lowest Reading Allowed | 0x06c0 | 1728 | Value | 2 | Minimum TPS reading |
| Throttle Position Sensor Default Value | 0x06c2 | 1730 | Value | 2 | TPS default value set on failure |
| O2 Sensor Test Minimum RPM | 0x06c4 | 1732 | Value | 2 | Minimum RPM to check for O2 activity |
| O2 Sensor Test Minimum Throttle | 0x06c6 | 1734 | Value | 1 | Minimum throttle to check for O2 activity |
| O2 Sensor Number of Errors | 0x06c7 | 1735 | Value | 1 | Number of O2 sensor read failures before error code is set |
| O2 Sensor Number of Inactive Reads | 0x06c8 | 1736 | Value | 1 | Number of inactive results before error code is set |
| Engine Temperature Sensor Number of Errors | 0x06c9 | 1737 | Value | 1 | Number of ET sensor read failures before error code is set |
| Engine Temperature Sensor Highest Reading Allowed | 0x06ca | 1738 | Value | 1 | Maximum ET sensor reading |
| Engine Temperature Sensor Lowest Reading Allowed | 0x06cb | 1739 | Value | 1 | Minimum ET sensor reading |
| Engine Temperature Sensor Default Value | 0x06cc | 1740 | Value | 1 | ET sensor default value set on failure |
| Air Temperature Sensor Highest Reading Allowed | 0x06cd | 1741 | Value | 1 | Maximum allowed air temperature sensor reading |
| Air Temperature Sensor Lowest Reading Allowed | 0x06ce | 1742 | Value | 1 | Minimum allowed air temperature sensor reading |
| Air Temperature Sensor Default Value | 0x06cf | 1743 | Value | 1 | Air temperature sensor default value, set on failure |
| Air Temperature Sensor Number of Errors | 0x06d0 | 1744 | Value | 1 | Number of air temperature sensor test failures before error code is set |
| Battery Average Voltage Difference Limit | 0x06d5 | 1749 | Value | 1 | Maximum difference allowed between average high and low battery voltage |
| Battery Voltage Test Minimum RPM | 0x06d6 | 1750 | Value | 1 | Minimum engine speed to perform battery voltage tests |
| Battery Voltage Number of Errors | 0x06d7 | 1751 | Value | 1 | Number of battery voltage test failures before error code is set |
| Battery Voltage Highest Reading Allowed | 0x06d8 | 1752 | Value | 2 | Battery voltage maximum reading allowed |
| Battery Voltage Lowest Reading Allowed | 0x06da | 1754 | Value | 2 | Battery voltage minimum reading allowed |
| Battery Voltage Default Value | 0x06dc | 1756 | Value | 2 | Battery voltage default value, set on failure |
| Active Muffler Controller Number of Tests Failed | 0x06de | 1758 | Value | 1 | Number of AMC test failures before error code is set |
| Active Muffler Controller Max Feedback Time | 0x06df | 1759 | Value | 1 | Maximum time allowed for AMC feedback |
| Active Intake Maximum TPS Reading Allowed | 0x06e0 | 1760 | Value | 1 | Maximum TPS reading while AIC is active |
| Active Intake Error Counts | 0x06e1 | 1761 | Value | 1 | Number of failed active intake tests before setting an error code |
| Active Intake Feedback Timeout | 0x06e2 | 1762 | Value | 1 | Active Intake Control feedback timeout |
| Injector Feedback Highest Reading Allowed | 0x06e3 | 1763 | Value | 1 | Maximum injector feedback reading |
| Injector Feedback Lowest Reading Allowed | 0x06e4 | 1764 | Value | 1 | Minimum injector feedback reading |
| Injector Feedback Number of Errors | 0x06e5 | 1765 | Value | 1 | Number of injector feedback test failures before error code is set |
| Coil Feedback Highest Reading Allowed | 0x06e6 | 1766 | Value | 1 | Maximum allowed coil feedback reading |
| Coil Feedback Lowest Reading Allowed | 0x06e7 | 1767 | Value | 1 | Minimum allowed coil feedback reading |
| Coil Feedback Number of Errors | 0x06e8 | 1768 | Value | 1 | Number of failed coil feedback tests before error code is set |
| Clutch Test Number of VSS Samples | 0x06e9 | 1769 | Value | 1 | Number of vehicle speed samples for clutch diagnostic tests |
| Clutch Test Minimum Load | 0x06ea | 1770 | Value | 1 | Minimum load to run clutch diagnostic tests |
| Clutch Test Timeout | 0x06eb | 1771 | Value | 1 | Number of failed clutch diagnostic tests before error code is set |
| Neutral Test Number of VSS Samples | 0x06ec | 1772 | Value | 1 | Number of vehicle speed samples for neutral diagnostic tests |
| Neutral Test Minimum Load | 0x06ed | 1773 | Value | 1 | Minimum load for neutral diagnostic |
| Neutral Test Timeout | 0x06ee | 1774 | Value | 1 | Neutral diagnostic timeout |
| Fuel Pump Feedback Upper Limit | 0x06ef | 1775 | Value | 1 | Maximum fuelpump feedback reading |
| Fuel Pump Feedback Off Time before Test | 0x06f0 | 1776 | Value | 1 | Off time before fuel pump feedback checked |
| Fuel Pump Feedback Number of Errors | 0x06f1 | 1777 | Value | 1 | Number of fuelpump feedback test failures before error code is set |
| Idle Air Control Position Test Maximum Engine Temperature | 0x06f5 | 1781 | Value | 1 | Maximum engine temperature to test idle air control position |
| Idle Air Control Position Test Limit High | 0x06f6 | 1782 | Value | 1 | IAC position high diagnostic limit 255 disables) |
| Idle Air Control Position Test Limit Low | 0x06f7 | 1783 | Value | 1 | IAC position low diagnostic limit |
| Idle Air Control Highest Reading Allowed | 0x06f8 | 1784 | Value | 1 | IAC high position limit |
| Idle Air Control Lowest Reading Allowed | 0x06f9 | 1785 | Value | 1 | IAC low position limit |
| Idle Air Control Position Test Timeout | 0x06fa | 1786 | Value | 1 | Idle air control position diagnostic timeout |
| Idle Air Control Test Timeout | 0x06fb | 1787 | Value | 1 | IAC diagnostic timeout |
| Tacho Feedback Number of Errors | 0x06fc | 1788 | Value | 1 | Number of tacho feedback test failures before error code is set |
| Fan Feedback Off Time before Test | 0x06fd | 1789 | Value | 1 | Fan off-time before running feedback test |
| Fan Feedback Number of Errors | 0x06fe | 1790 | Value | 1 | Number of failed fan tests before error code is set |
| VSS Output Test Timeout | 0x06ff | 1791 | Value | 1 | Vehicle Speed Ouptut diagnostic timeout |
| VSS Input Test Minimum RPM | 0x0700 | 1792 | Value | 1 | Minimum engine speed for VS input diagnostic |
| VSS Input Test Minimum Load | 0x0701 | 1793 | Value | 1 | Minimum load for VS input diagnostic |
| VSS Input Test Timeout | 0x0702 | 1794 | Value | 1 | Vehicle Speed Input diagnostic timeout |
| Bank Angle Sensor Highest Reading Allowed | 0x0705 | 1797 | Value | 1 | Maximum bank angle sensor reading allowed (alternative: shifter configuration) |
| Bank Angle Sensor Tip-Over Value | 0x0706 | 1798 | Value | 1 | Bank angle sensor tip-over value (alternative: shifter minimum delay between activations) |
| Bank Angle Sensor Lowest Reading Allowed | 0x0707 | 1799 | Value | 1 | Minimum bank angles sensor reading allowed (alternative: shifter debounce period) |
| Bank Angle Sensor Number of Errors | 0x0708 | 1800 | Value | 1 | Number of bank angle sensor test failures before error code is set (alternative: shifter fuel cut duration) |
| Bank Angle Sensor Tipover Delay | 0x0709 | 1801 | Value | 1 | Bank angle sensor tip-over detection delay (alternative: shifter maximum input activation value) |
| Starter Relay Test Timeout | 0x070a | 1802 | Value | 1 | Starter Relay diagnostic timeout |
| Aux Power Relay Test Feedback Timeout | 0x070b | 1803 | Value | 1 | Auxiliary Power Relay diagnostic timeout |
| EEPROM Test Number of Errors | 0x070c | 1804 | Value | 1 | Number of failed EEPROM checksum tests before error code set |
| AD-Converter Number of Errors | 0x070d | 1805 | Value | 1 | Number of failed A/D conversion tests before error code set |
| Camshaft Sensor Test Minimum RPM | 0x070e | 1806 | Value | 2 | Minimum RPM to set lost sync error |
| Camshaft Sensor Number of Sync Errors | 0x0710 | 1808 | Value | 1 | Number of revs without sync detected before error code set |
| Camshaft Sensor Test Number of Consecutive Sync Errors | 0x0711 | 1809 | Value | 1 | Number of consecutive out-of-sync revs before error code set |
| AFV Cylinder Difference Limit | 0x0715 | 1813 | Value | 1 | Learned Fuel Cylinder Difference limit |
| AFV Cylinder Difference Number of Errors | 0x0716 | 1814 | Value | 1 | Learned Fuel Cylinder Difference timeout |
| MAP Sensor Highest Reading Allowed | 0x0717 | 1815 | Value | 1 | Highest MAP sensor reading allowed |
| MAP Sensor Lowest Reading Allowed | 0x0718 | 1816 | Value | 1 | Lowest MAP sensor reading allowed |
| MAP Sensor Default Value | 0x0719 | 1817 | Value | 1 | Default MAP value set on failure |
| Map Sensor Number of Errors | 0x071a | 1818 | Value | 1 | Number of MAP sensor read failures before error code is set |
| Barometric Pressure Sensor Highest Reading Allowed | 0x071b | 1819 | Value | 1 | Barometric pressure sensor maximum reading allowed |
| Barometric Pressure Sensor Lowest Reading Allowed | 0x071c | 1820 | Value | 1 | Barometric pressure sensor mininmum reading allowed |
| Barometric Pressure Sensor Default Value | 0x071d | 1821 | Value | 1 | Barometric pressure sensor default value, set on failure |
| Barometric Pressure Sensor Number of Errors | 0x071e | 1822 | Value | 1 | Number of barometric pressure sensor test failures before error code is set |
| Error Mask Byte 0 | 0x0729 | 1833 | Bits | 1 | Diagnostic trouble code mask, byte 0 |
| Error Mask Byte 1 | 0x072a | 1834 | Bits | 1 | Diagnostic trouble code mask, byte 1 |
| Error Mask Byte 2 | 0x072b | 1835 | Bits | 1 | Diagnostic trouble code mask, byte 2 |
| Error Mask Byte 3 | 0x072c | 1836 | Bits | 1 | Diagnostic trouble code mask, byte 3 |
| Error Mask Byte 4 | 0x072d | 1837 | Bits | 1 | Diagnostic trouble code mask, byte 4 |
| Error Mask Byte 5 | 0x072e | 1838 | Bits | 1 | Diagnostic trouble code mask, byte 5 |
| Error Mask Byte 6 | 0x072f | 1839 | Bits | 1 | Diagnostic trouble code mask, byte 6 |
| Error Mask Byte 7 | 0x0730 | 1840 | Bits | 1 | Diagnostic trouble code mask, byte 7 |
| Error Mask Byte 8 | 0x0731 | 1841 | Bits | 1 | Diagnostic trouble code mask, byte 8 |
| Error Mask Byte 9 | 0x0732 | 1842 | Bits | 1 | Diagnostic trouble code mask, byte 9 |
| Error Mask Byte 10 | 0x0733 | 1843 | Bits | 1 | Diagnostic trouble code mask, byte 10 |
| Dwell Duration | 0x0735 | 1845 | Array | 17 | Dwell duration table |
| Timing Table Load Axis | 0x0746 | 1862 | Axis | 10 | Timing table load axis y-axis) |
| Timing Table RPM Axis | 0x0750 | 1872 | Axis | 36 | Timing table RPM axis x-axis) |
| Fuel Map Load Axis | 0x0774 | 1908 | Axis | 16 | Fuel load axis |
| Fuel Map RPM Axis | 0x0784 | 1924 | Axis | 40 | Fuel RPM axis |
| 2nd Fuel Map Load Axis | 0x07ac | 1964 | Axis | 8 | Secondary injector load axis |
| 2nd Fuel Map RPM Axis | 0x07b4 | 1972 | Axis | 24 | Secondary injector RPM axis |
| Timing Table Front | 0x0800 | 2048 | Map | 180 | Timing table front cylinder |
| Timing Table Rear | 0x08b4 | 2228 | Map | 180 | Timing table rear cylinder |
| Fuel Map Front | 0x0968 | 2408 | Map | 320 | Front fuel table |
| Fuel Map Rear | 0x0aa8 | 2728 | Map | 320 | Fuel map rear cylinder |
| 2nd Fuel Map Front | 0x0be8 | 3048 | Map | 96 | Front showerhead table |
| 2nd Fuel Map Rear | 0x0c48 | 3144 | Map | 96 | Rear showerhead table |
| Air Temperature Maximum Spark Advance Reduction | 0x0ca8 | 3240 | Map | 180 | Maximum TA spark retard |
| TP to Load Table TP Axis | 0x0d84 | 3460 | Axis | 8 | Throttle position axis for TP to load conversion map |
| TP to Load Table RPM Axis | 0x0d8c | 3468 | Axis | 16 | RPM axis for TP to load conversion map |
| TP to Load Table | 0x0d9c | 3484 | Map | 64 | Throttle position to load conversion map |
| MAP to Load Table MAP Axis | 0x0ddc | 3548 | Axis | 8 | MAP axis for MAP to load conversion map |
| MAP to Load Table RPM Axis | 0x0de4 | 3556 | Axis | 16 | RPM axis for MAP to load conversion map |
| MAP to Load Table Front | 0x0df4 | 3572 | Map | 64 | Convert front MAP to load |
| MAP to Load Table Rear | 0x0e34 | 3636 | Map | 64 | Convert rear MAP to load |
| TP to Load Weight Table TP Axis | 0x0e74 | 3700 | Axis | 8 | Throttle position axis for TP to load weight map |
| TP to Load Weight Table RPM Axis | 0x0e7c | 3708 | Axis | 16 | RPM axis for TP to load weight map |
| TP to Load Weight Table | 0x0e8c | 3724 | Map | 64 | Weight of TPS vs MAP) in load calculation |
Note:
For variables that have a scaling factor and/or a translational offset given, use this formula to calculate the output value:
output_value = (EEPROM_value * scale) + translate
Please double-check all information from this site before using them!