| Name/Meaning | Offset | Type | Size (bytes) | Remark | |
|---|---|---|---|---|---|
| AFV Front | 0xffffffffffffffea | -22 | Value | 2 | Adaptive fuel value front cylinder |
| Idle Air Control Average Position | 0xffffffffffffffed | -19 | Value | 1 | Average IAC position when PID control is active |
| Active Intake Actuations | 0xffffffffffffffee | -18 | Value | 2 | Count of Active Intake actuations since cleared |
| AMC Key-On Status | 0xfffffffffffffff6 | -10 | Bits | 1 | AMC status when ignition is switched on |
| Baro Pressure Sensor Stored Value | 0xfffffffffffffff8 | -8 | Value | 1 | Stored barometric sensor reading |
| Stored Error Byte 0 | 0xfffffffffffffff9 | -7 | Bits | 1 | Stored (historic) trouble codes, byte 0 |
| Stored Error Byte 1 | 0xfffffffffffffffa | -6 | Bits | 1 | Stored (historic) trouble codes, byte 1 |
| Stored Error Byte 2 | 0xfffffffffffffffb | -5 | Bits | 1 | Stored (historic) trouble codes, byte 2 |
| Stored Error Byte 3 | 0xfffffffffffffffc | -4 | Bits | 1 | Stored (historic) trouble codes, byte 3 |
| Stored Error Byte 4 | 0xfffffffffffffffd | -3 | Bits | 1 | Stored (historic) trouble codes, byte 4 |
| Stored Error Byte 5 | 0xfffffffffffffffe | -2 | Bits | 1 | Stored (historic) trouble codes, byte 5 |
| Stored Error Byte 6 | 0xffffffffffffffff | -1 | Bits | 1 | Stored (historic) trouble codes, byte 6 |
| Stored Error Byte 7 | 0x0000 | 0 | Bits | 1 | Stored (historic) trouble codes, byte 7 |
| Stored Error Byte 8 | 0x0001 | 1 | Bits | 1 | Stored (historic) trouble codes, byte 8 |
| Stored Error Byte 9 | 0x0002 | 2 | Bits | 1 | Stored (historic) trouble codes, byte 9 |
| Stored Error Byte 10 | 0x0003 | 3 | Bits | 1 | Stored (historic) trouble codes, byte 10 |
| Number of Rides since Error Set | 0x0004 | 4 | Value | 1 | Number of rides since a trouble code was set |
| Calibration ID | 0x0005 | 5 | Value | 1 | Country specific calibration identifier |
| AFV Rear | 0x0006 | 6 | Value | 2 | Adaptive fuel value rear cylinder |
| System Configuration | 0x0008 | 8 | Bits | 1 | Global ECM setup |
| Layout Revision | 0x0009 | 9 | Value | 1 | Cal Structure Revision read only) |
| Engine Running RPM Hysteresis High Value | 0x000e | 14 | Value | 2 | Upper engine running threshold |
| Engine Running RPM Hysteresis Low Value | 0x0010 | 16 | Value | 2 | Lower engine running threshold |
| Throttle Position Sensor Reset Voltage | 0x0012 | 18 | Value | 2 | TPS voltage with a fully closed throttle, written on a TPS reset |
| Throttle Position Sensor Voltage Range | 0x0014 | 20 | Value | 2 | TPS voltage difference from fully closed to WOT |
| Throttle Position Sensor Degrees Range | 0x0016 | 22 | Value | 2 | TPS degrees difference from fully closed to WOT |
| Throttle Position Sensor Moving Average Fraction | 0x0018 | 24 | Value | 1 | TPS fraction used to detect TP changes |
| O2 Sensor Rich Voltage | 0x001e | 30 | Value | 1 | O2 sensor voltage indicating a rich mixture |
| O2 Sensor Lean Voltage | 0x001f | 31 | Value | 1 | O2 sensor voltage indicating a lean mixture |
| Closed Loop Feature Minimum RPM | 0x0020 | 32 | Value | 1 | Minimum RPM to activate O2 sensor |
| Closed Loop Feature Minimum Throttle | 0x0021 | 33 | Value | 1 | Minimum throttle to activate O2 sensor |
| O2 Sensor Activation Time | 0x0022 | 34 | Value | 1 | O2 sensor activation delay |
| O2 Sensor Deactivation Time | 0x0023 | 35 | Value | 1 | O2 sensor deactivation delay |
| Startup Fuel Pulsewidth | 0x0024 | 36 | Table | 6 | Starting fuel pulse length |
| Pre Sync Fuel Maximum Engine Temperature | 0x002a | 42 | Value | 1 | Max engine temp for pre-sync fuel pulses |
| Post Sync Fuel Maximum Engine Temperature | 0x002b | 43 | Value | 1 | Max engine temp for post-sync fuel pulses |
| Fuel Pump Duty Cycle Table | 0x002c | 44 | Table | 6 | Fuel pump duty cycle table |
| Fuel Pump Frequency | 0x0032 | 50 | Value | 1 | Fuel pump PWM frequency |
| AD-Converter Input Select | 0x0033 | 51 | Value | 1 | Analog-digital conversion input |
| MAP Sensor Front Reading Position | 0x0034 | 52 | Value | 1 | Crankshaft position to read front MAP sensor |
| MAP Sensor Rear Reading Position | 0x0035 | 53 | Value | 1 | Crankshaft position to read rear MAP sensor |
| TPS-MAP Load Configuration | 0x0036 | 54 | Bits | 1 | Throttle Map Load Configuration |
| Live Log Configuration | 0x0038 | 56 | Bits | 1 | Live Log Configuration |
| Global Fuel Correction | 0x003a | 58 | Value | 1 | Global fuel correction factor, applied to all map regions |
| Acceleration Enrichment Configuration | 0x003b | 59 | Bits | 1 | Acceleration Enrichment Configuration |
| Acceleration Enrichment Front Pulse Start | 0x003d | 61 | Value | 1 | Camshaft or crankshaft position to start late acceleration pulse for the front cylinder |
| Acceleration Enrichment Rear Pulse Start | 0x003e | 62 | Value | 1 | Camshaft or crankshaft position to start late acceleration pulse for the rear cylinder |
| Light Acceleration Condition | 0x003f | 63 | Value | 1 | TPS change indicating a light accel. condition |
| Full Acceleration Condition | 0x0040 | 64 | Value | 1 | Change in throttle movement indicationg a full acceleration condition |
| Acceleration Enrichment Duration | 0x0041 | 65 | Value | 1 | Full acceleration enrichment duration in engine revs |
| Acceleration Enrichment Region | 0x0042 | 66 | Table | 4 | Acceleration enrichment region |
| Acceleration Enrichment Temperature Adjustment | 0x0046 | 70 | Table | 8 | Acceleration enrichment adjustment on engine temperature |
| Acceleration Enrichment | 0x004e | 78 | Table | 8 | Acceleration enrichment |
| Deceleration Correction Region | 0x0056 | 86 | Table | 8 | Deceleration correction region |
| Deceleration Correction | 0x005e | 94 | Value | 1 | Deceleration correction |
| Deceleration Condition Hysteresis | 0x005f | 95 | Value | 1 | Deceleration condition throttle hysteresis |
| Throttle Roll-Off Condition | 0x0060 | 96 | Value | 1 | Throttle roll-off condition |
| Throttle Roll-Off Correction | 0x0061 | 97 | Value | 1 | Throttle roll-off fuel correction |
| Fuel Cut Region | 0x0062 | 98 | Table | 4 | Fuel cut region |
| Deceleration Learn Maximum RPM | 0x0066 | 102 | Value | 1 | Deceleration learn mode maximum RPM |
| Deceleration Learn Minimum RPM | 0x0067 | 103 | Value | 1 | Deceleration learn mode minimum RPM |
| Deceleration Learn Minimum Duration | 0x0068 | 104 | Value | 1 | Engine revs for deceleration learn mode |
| Deceleration Learn Minimum Readings | 0x0069 | 105 | Value | 1 | Number of consecutive rich O2 readings required |
| WOT Region | 0x006a | 106 | Table | 4 | Wide-Open Throttle definition |
| WOT Enrichment | 0x006e | 110 | Value | 2 | Default fuel correction, applied to WOT regions |
| Idle Correction | 0x0070 | 112 | Table | 8 | Idle correction |
| Idle Maximum Engine Speed | 0x0078 | 120 | Value | 2 | Idle region maximum RPM |
| Idle Maximum Load | 0x007a | 122 | Value | 1 | Idle region maximum load |
| Open Loop Enrichment Delay | 0x007b | 123 | Value | 1 | Time before increasing AFV |
| Startup Enrichment Temperature Axis | 0x007c | 124 | Axis | 4 | Startup condition temperature axis |
| Startup Enrichment | 0x0080 | 128 | Map | 4 | Fuell correction after egine startup |
| Startup Enrichment Duration | 0x0084 | 132 | Map | 4 | Duration of startup fuel enrichment |
| Open Loop Default Correction | 0x0088 | 136 | Value | 2 | Default fuel correction, applied to open loop regions |
| Front Cylinder Correction | 0x008a | 138 | Table | 8 | Front cylinder fuel enrichment on engine temperature |
| Warmup Enrichment | 0x0092 | 146 | Table | 28 | Engine temperature fuel correction |
| Hot Start Condition | 0x00ae | 174 | Value | 2 | Engine temperature indicating a hot start condition |
| Engine Temperature Sensor Conversion Data | 0x00b0 | 176 | Table | 28 | Engine temperature senor data |
| Air Temperature Correction | 0x00cc | 204 | Table | 14 | Air Temp correction |
| Air Temperature Sensor Data | 0x00da | 218 | Table | 28 | Air temperature sensor data |
| Battery Voltage Correction | 0x00f6 | 246 | Table | 12 | Battery voltage correction |
| 2nd Battery Voltage Correction | 0x0102 | 258 | Table | 12 | Battery correction for showerheads |
| Barometric Pressure Sensor Reading Configuration | 0x010e | 270 | Bits | 1 | Barometric pressure sensor access setup |
| Baro Pressure Sensor Delay | 0x010f | 271 | Value | 1 | Delay before reading barometric pressure sensor when switching on ignition |
| Barometric Feature Region | 0x0110 | 272 | Table | 8 | Barometric feature region lower boundary |
| MAP Barometric Correction | 0x0118 | 280 | Table | 8 | Baro adjustment of MAP reads |
| Baro Pressure Sensor Moving Average Factor | 0x0120 | 288 | Value | 1 | Baro Pressure Sensor Moving Average Factor |
| Airbox Pressure Configuration | 0x0121 | 289 | Bits | 1 | Air pressure sensor configuration byte |
| Barometric Pressure Key-On Minimum Value | 0x0122 | 290 | Value | 1 | Minimum valid barometric pressure sensor reading when switching on ignition |
| Barometric Pressure Key-On Maximum Value | 0x0123 | 291 | Value | 1 | Maximum valid barometric pressure sensor reading when switching on ignition |
| Airbox Pressure Sensor Data | 0x0124 | 292 | Table | 14 | Air Box Pressure conversion |
| Baro Correction | 0x0132 | 306 | Table | 14 | Baro pressure correction |
| Vehicle Speed Correction | 0x0140 | 320 | Table | 16 | Airbox pressure correction for speed |
| Airbox Pressure Correction | 0x0150 | 336 | Table | 16 | Airbox pressure correction |
| Closed Loop Configuration | 0x0160 | 352 | Bits | 1 | Fuel closed loop setup |
| Calibration Mode Number of Readings | 0x0161 | 353 | Value | 1 | Number of O2 sensor readings required to adjust AFV |
| Closed Loop Region Upper Boundary | 0x0162 | 354 | Table | 8 | Closed loop upper boundary |
| Closed Loop Region Lower Boundary | 0x016a | 362 | Table | 18 | Closed loop lower boundary |
| Closed Loop Upper Boundary Load Hysteresis | 0x017c | 380 | Value | 1 | Upper closed loop boundary hysteresis, TPP |
| Closed Loop Lower Boundary Load Hysteresis | 0x017d | 381 | Value | 1 | Lower closed loop boundary hysteresis, TPP |
| Closed Loop Upper Boundary RPM Hysteresis | 0x017e | 382 | Value | 2 | Closed loop upper boundary RPM hysteresis |
| Closed Loop Lower Boundary RPM Hysteresis | 0x0180 | 384 | Value | 2 | Closed loop lower boundary RPM hysteresis |
| EGO Correction Maximum Value | 0x0182 | 386 | Value | 2 | Maximum closed loop EGO correction |
| EGO Correction Minimum Value | 0x0184 | 388 | Value | 2 | Minimum closed loop EGO correction |
| Closed Loop Maximum Engine Temperature | 0x0186 | 390 | Value | 2 | Maximum engine temperature to activate closed loop |
| Closed Loop Minimum Engine Temperature | 0x0188 | 392 | Value | 2 | Minimum engine temperature to activate closed loop |
| Closed Loop Lower Boundary Adjustment Value | 0x018a | 394 | Value | 1 | Lower closed loop region boundary adjustment value |
| Closed Loop Lower Boundary Adjustment Highest Gear | 0x018b | 395 | Value | 1 | Highest gear where lower closed loop region boundary is adjusted |
| AFV Maximum Value | 0x018c | 396 | Value | 2 | Maximum allowed AFV |
| AFV Minimum Value | 0x018e | 398 | Value | 2 | Minimum allowed AFV |
| AFV Increase Factor | 0x0190 | 400 | Value | 2 | Factor applied to increase AFV |
| AFV Decrease Factor | 0x0192 | 402 | Value | 2 | Factor applied to decrease AFV |
| Calibration Mode Maximum Engine Temperature | 0x0194 | 404 | Value | 2 | Maximum engine temperature to enable calibration mode |
| Calibration Mode Minimum Engine Temperature | 0x0196 | 406 | Value | 2 | Minimum engine temperature to enable calibration mode |
| Calibration Mode Region Upper Boundary | 0x0198 | 408 | Table | 8 | Calibration mode region upper boundary |
| Calibration Mode Region Lower Boundary | 0x01a0 | 416 | Table | 14 | Calibration mode region lower boundary |
| Altitude Adjustement Lower Boundary | 0x01ae | 430 | Table | 6 | Altitude adjustment lower boundary |
| Altitude Adjustment Upper Boundary | 0x01b4 | 436 | Table | 6 | Altitude adjustment upper boundary |
| Fuel PI Controller Low RPM Threshold | 0x01ba | 442 | Value | 1 | PI controller low value RPM limit |
| Fuel PI Controller Low Load Threshold | 0x01bb | 443 | Value | 1 | PI controller low value load limit |
| Fuel PI Controller High RPM Threshold | 0x01bc | 444 | Value | 1 | PI controller high value RPM limit |
| Fuel PI Controller High Load Threshold | 0x01bd | 445 | Value | 1 | PI controller high value load limit |
| O2 Sensor Target Voltage Array | 0x01be | 446 | Array | 4 | O2 midpoint for idle, lo, mid and hi |
| Fuel PI Controller P-Value Table Front when Rich | 0x01c2 | 450 | Array | 4 | Proportional values for the front cylinder and rich transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Front when Rich | 0x01c6 | 454 | Array | 4 | Integral values for the front cylinder and rich mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Front when Lean | 0x01ca | 458 | Array | 4 | Proportional values for the front cylinder and lean transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Front when Lean | 0x01ce | 462 | Array | 4 | Integral values for the front cylinder and lean mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Rear when Rich | 0x01d2 | 466 | Array | 4 | Proportional values for the rear cylinder and rich transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Rear when Rich | 0x01d6 | 470 | Array | 4 | Integral values for the rear cylinder and rich mixture (idle, low, mid, high) |
| Fuel PI Controller P-Value Table Rear when Lean | 0x01da | 474 | Array | 4 | Proportional values for the rear cylinder and lean transition (idle, low, mid, high) |
| Fuel PI Controller I-Value Table Rear when Lean | 0x01de | 478 | Array | 4 | Integral values for the rear cylinder and lean mixture (idle, low, mid, high) |
| Fuel Pulse Endpoint Table for Engine Temperature | 0x01e8 | 488 | Table | 6 | Fuel pulse endpoint temperature correction |
| Fuel Pulse Endpoint Table for Load | 0x01ee | 494 | Table | 6 | Fuel pulse endpoint throttle correction |
| 2nd Fuel Puls Endpoint Temperature Correction | 0x01f4 | 500 | Table | 6 | Showerhead pulse end point, ET based |
| 2nd Fuel Pulse Endpoint Throttle Correction | 0x01fa | 506 | Table | 6 | Showerhead pulse end point, load based |
| Table Lock Value | 0x0200 | 512 | Value | 2 | |
| AFV Storage Delay | 0x0202 | 514 | Value | 1 | Time between AFV writes to EEPROM |
| Global Spark Advance | 0x0203 | 515 | Value | 1 | Global spark advance adjustment |
| Timed Spark Adjust Minimum RPM | 0x0204 | 516 | Value | 2 | Minimum RPM to enable spark advance adjusting |
| Idle Spark Advance Table | 0x0206 | 518 | Table | 8 | Idle Spark Advance |
| WOT Spark Advance Reduction | 0x020e | 526 | Table | 8 | WOT spark advance reduction |
| Air Temperature Spark Retard Configuration | 0x0216 | 534 | Bits | 1 | Air Temp Retard Configuration |
| Air Temperature Spark Advance Reduction Scaling | 0x0218 | 536 | Table | 14 | Air temp spark retard |
| VSS Input Minimum Frequency | 0x0227 | 551 | Value | 1 | Minimum valid VSS input frequency |
| VSS Input Scaling Factor | 0x0228 | 552 | Value | 1 | Scale factor for VSS input |
| VSS Output Scaling Factor | 0x022a | 554 | Value | 1 | Scale factor for VSS output |
| VS-RPM Ratio VS Sampling Time | 0x022c | 556 | Value | 2 | Time to count speed sensor pulses |
| Speed-RPM Ratio RPM Sample Duration | 0x022d | 557 | Value | 1 | Sample period for Speed-RPM ratio |
| VSS Ratio Gearing Table | 0x022e | 558 | Array | 6 | Gear selection |
| Spark Advance Retard Configuration | 0x0234 | 564 | Bits | 1 | Spark advance and fuel reduction configuration |
| Spark Advance Retard Minimum Engine Temperature | 0x0235 | 565 | Value | 1 | Minimum engine temperature to enable reduction |
| Spark Advance Reduction Upper RPM Boundary | 0x0236 | 566 | Array | 7 | Maximum RPM to enable reduction |
| Spark Advance Reduction Lower RPM boundary | 0x023d | 573 | Array | 7 | Minimum RPM to enable reduction |
| Spark Advance Reduction Fuel Correction | 0x0244 | 580 | Array | 7 | Fuel correction during activation |
| Spark Advance Reduction | 0x024b | 587 | Array | 7 | The spark advance reduction while noise abatement is active |
| Spark Advance Reduction Ramp-In Duration | 0x0252 | 594 | Array | 7 | Spark advance reduction ramp-in duration |
| Spark Advance Reduction Hold Duration | 0x0259 | 601 | Array | 7 | Spark advance reduction hold duration |
| Spark Advance Reduction Ramp-Out Duration | 0x0260 | 608 | Array | 7 | Spark advance reduction ramp-out duration |
| Active Intake Configuration | 0x0267 | 615 | Bits | 1 | Active intake controller setup |
| Active Intake Gearing | 0x0268 | 616 | Bits | 1 | Active intake gearing configuration byte |
| Active Intake Period | 0x0269 | 617 | Value | 1 | Active intake control period |
| Active Intake Ramp In Duty Cycle | 0x026a | 618 | Value | 1 | Active intake ramp-in period duty cycle |
| Active Intake Hold Duty Cycle | 0x026b | 619 | Value | 1 | Active intake hold period duty cycle |
| Active Intake Ramp Out Duty Cycle | 0x026c | 620 | Value | 1 | Active intake ramp-out period duty cycle |
| Fuel and Spark Skip Configuation | 0x026d | 621 | Bits | 1 | Fuel and Spark Skip Configuation |
| RPM Fixed Limit Cold Start Ramp | 0x026e | 622 | Value | 1 | Temperature delta to ramp from cold RPM limits |
| Soft Limit Ignition Pattern Front | 0x026f | 623 | Value | 1 | Front Soft Limit Fire Pattern |
| Soft Limit Ignition Pattern Rear | 0x0270 | 624 | Value | 1 | Rear Soft Limit Fire Pattern |
| Hard Limit Ignition Pattern Front | 0x0271 | 625 | Value | 1 | Front Hard Limit Fire Pattern |
| Hard Limit Ignition Pattern Rear | 0x0272 | 626 | Value | 1 | Rear Hard Limit Fire Pattern |
| RPM Fixed Soft Limit Trigger for Cold Engine | 0x0273 | 627 | Value | 1 | Cold engine soft RPM limit, high |
| RPM Fixed Soft Limit Recharge for Cold Engine | 0x0274 | 628 | Value | 1 | Cold engine soft RPM limit, low |
| RPM Fixed Hard Limit Trigger for Cold Engine | 0x0275 | 629 | Value | 1 | Cold engine hard RPM limit, high |
| RPM Fixed Hard Limit Recharge for Cold Engine | 0x0276 | 630 | Value | 1 | Cold engine hard RPM limit, low |
| RPM Fixed Soft Limit Trigger | 0x0277 | 631 | Value | 1 | Fixed soft limit trigger RPM |
| RPM Fixed Soft Limit Recharge | 0x0278 | 632 | Value | 1 | Fixed soft limit release RPM |
| RPM Fixed Hard Limit Trigger | 0x0279 | 633 | Value | 1 | Fixed hard limit trigger RPM |
| RPM Fixed Hard Limit Recharge | 0x027a | 634 | Value | 1 | Fixed hard limit release RPM |
| RPM Fixed Kill Limit Trigger | 0x027b | 635 | Value | 1 | Kill limit trigger RPM |
| RPM Fixed Kill Limit Recharge | 0x027c | 636 | Value | 1 | Kill limit release RPM |
| RPM High Speed Hysteresis High Value | 0x027d | 637 | Value | 1 | High speed speed-RPM-ratio hysteresis, upper value |
| RPM High Speed Hysteresis Low Value | 0x027e | 638 | Value | 1 | High speed speed-RPM-ratio hysteresis, lower value |
| RPM High Speed Timed Limit Timer Start | 0x027f | 639 | Value | 1 | RPM threshold to start limit timer at high speed |
| RPM High Speed Timed Limit Timer Reset | 0x0280 | 640 | Value | 1 | RPM threshold to reset limit timer at high speed |
| RPM High Speed Timed Hard Limit | 0x0281 | 641 | Value | 1 | RPM threshold to enable delayed hard limit at high speed |
| RPM High Speed Timed Soft Limit | 0x0282 | 642 | Value | 1 | RPM threshold to enable delayed soft limit at high speed |
| RPM High Speed Timed Soft Limit Delay | 0x0283 | 643 | Value | 1 | Soft limit delay at high speed |
| RPM High Speed Timed Hard Limit Delay | 0x0284 | 644 | Value | 1 | Hard limit delay at high speed |
| RPM Low Speed Timed Limit Timer Start | 0x0285 | 645 | Value | 1 | RPM threshold to start limit timer at low speed |
| RPM Low Speed Timed Limit Timer Reset | 0x0286 | 646 | Value | 1 | RPM threshold to reset limit timer at low speed |
| RPM Low Speed Timed Hard Limit | 0x0287 | 647 | Value | 1 | RPM threshold to enable delayed hard limit at low speed |
| RPM Low Speed Timed Soft Limit | 0x0288 | 648 | Value | 1 | RPM threshold to enable delayed soft limit at low speed |
| RPM Low Speed Timed Soft Limit Delay | 0x0289 | 649 | Value | 1 | Soft limit delay at low speed |
| RPM Low Speed Timed Hard Limit Delay | 0x028a | 650 | Value | 1 | Hard limit delay at low speed |
| Temperature Soft Limit Minimum Load | 0x028b | 651 | Value | 1 | Load above which soft temp limit enabled |
| Temperature Soft Limit Minimum RPM | 0x028c | 652 | Value | 1 | Minimum RPM to enable temperature soft limit |
| Temperature Hard Limit Minimum Load | 0x028d | 653 | Value | 1 | Load above which hard temp limit enabled |
| Temperature Hard Limit Minimum RPM | 0x028e | 654 | Value | 1 | Minimum RPM to enable temperature hard limit |
| Temperature Soft Limit Trigger | 0x028f | 655 | Value | 1 | Temperature threshold to trigger soft limit |
| Temperature Soft Limit Recharge | 0x0290 | 656 | Value | 1 | Temperature threshold to recharge soft limit |
| Temperature Hard Limit Trigger | 0x0291 | 657 | Value | 1 | Temperature trheshold to trigger hard limit |
| Temperature Hard Limit Recharge | 0x0292 | 658 | Value | 1 | Temperature threshold to recharge hard limit |
| Ignore Minimum RPM Trigger | 0x0293 | 659 | Value | 1 | Temperature threshold indicating to ignore RPM/throttle limits |
| Ignore Minimum RPM Recharge | 0x0294 | 660 | Value | 1 | Temperature threshold indicating to obey RPM/throttle limits |
| Temperature Kill Limit Trigger | 0x0295 | 661 | Value | 1 | Temperature trheshold to trigger hard limit |
| Temperature Kill Limit Recharge | 0x0296 | 662 | Value | 1 | Temperature threshold to recharge kill limit |
| Temperature Limit Engine Lamp On Value | 0x0297 | 663 | Value | 1 | Temperature threshold to switch on engine lamp |
| Temperature Limit Engine Lamp Off Value | 0x0298 | 664 | Value | 1 | Temperature threshold to switch off engine lamp |
| Fan Configuration | 0x0299 | 665 | Bits | 1 | Fan Configuration |
| Fan Key-On On Temperature | 0x029a | 666 | Value | 1 | Temperature threshold to switch on fan |
| Fan Key-On Off Temperature | 0x029b | 667 | Value | 1 | Temperature threshold to switch off fan |
| Fan Key-On Duty Cycle | 0x029c | 668 | Table | 8 | Fan key-on duty cycle |
| Fan Duty Cycle Period | 0x02a4 | 676 | Value | 1 | Cooling Fan Control Period |
| Fan Key-Off Run Delay | 0x02a5 | 677 | Value | 1 | Key-off delay before starting fan |
| Fan Key-Off Run Duty Cycle | 0x02a6 | 678 | Value | 1 | Fan duty cycle after key-off |
| Fan Key-Off On Temperature | 0x02a7 | 679 | Value | 1 | Key-off temperature threshold to switch on fan |
| Fan Key-Off Off Temperature | 0x02a8 | 680 | Value | 1 | Key-off temperature threshold to switch off fan |
| Fan Key-Off Maximum Duration | 0x02a9 | 681 | Value | 1 | Maximum time running fan after key-off |
| Fan Key-Off Minimum Battery Voltage | 0x02aa | 682 | Value | 1 | Minimum battery voltage to run fan after key-off |
| Fan 2 Delay | 0x02ab | 683 | Value | 1 | Delay before switching on fan 2 after turning on fan 1 |
| Active Muffler Configuration | 0x02ac | 684 | Bits | 1 | Active Muffler Valve Configuration |
| Active Muffler WOT Condition Hysteresis | 0x02ad | 685 | Value | 1 | Active exhaust valve WOT condition hysteresis |
| Active Muffler Motor Minimum On Time | 0x02ae | 686 | Value | 1 | Active exhaust valve controller minimum on-time |
| Active Muffler Motor Minimum Off Time | 0x02af | 687 | Value | 1 | Active exhaust valve controller minimum off-time |
| Active Muffler Valve Switching Points | 0x02b0 | 688 | Array | 6 | Active exhaust valve switching RPMs |
| Shifter Configuration | 0x02f0 | 752 | Bits | 1 | Shifter configuration |
| Shifter Input | 0x02f1 | 753 | Value | 1 | Input pin for shifter feature |
| Shifter Input Activation Level | 0x02f2 | 754 | Value | 1 | Shifter feature activation voltage |
| Shifter Input Debounce Time | 0x02f3 | 755 | Value | 1 | Shifter feature debounce time |
| Shifter Input Minimum Delay | 0x02f4 | 756 | Value | 1 | Minimum wait time between shifts |
| Shifter Interrupt Duration | 0x02f5 | 757 | Array | 7 | Length of shift interrupt |
| Shift Light Configuration | 0x02fc | 764 | Bits | 1 | Shift Light Configuration |
| Shift Light Flashing Period | 0x02fd | 765 | Value | 1 | Shift light on time while flashing |
| Shift Light Flashing RPM Hysteresis High | 0x02fe | 766 | Array | 7 | Shift Light flashing above this speed |
| Shift Light Flashing RPM Hysteresis Low | 0x0305 | 773 | Array | 7 | Shift Light stops flashing below this speed |
| Shift Light On RPM Hysteresis High | 0x030c | 780 | Array | 7 | Shift Light on above this speed |
| Shift Light Off RPM Hysteresis Low | 0x0313 | 787 | Array | 7 | Shift Light off below this speed |
| Starter Interlock Configuration | 0x031a | 794 | Bits | 1 | Starter Interlock Configuration |
| Sidestand Interlock Signal Threshold | 0x031b | 795 | Value | 1 | Threshold for sidestand input |
| Starter Relay Maximum RPM Hysteresis High | 0x031c | 796 | Value | 1 | Max RPM for starter relay upper hysteresis |
| Starter Relay Maximum RPM Hysteresis Low | 0x031d | 797 | Value | 1 | Max RPM for starter relay lower hysteresis |
| Sidestand Interlock Maximum Speed | 0x031e | 798 | Value | 1 | Sidestand interlock disabled after reaching speed |
| Sidestand Input Number of Errors | 0x031f | 799 | Value | 1 | Sidestand extended at high speed before failure |
| Sidestand Input Maximum Reading Allowed | 0x0320 | 800 | Value | 1 | Upper limit of sidestand input |
| Sidestand Input Minimum Reading Allowed | 0x0321 | 801 | Value | 1 | Lower limit of sidestand input |
| Idle Air Control Configuration | 0x0322 | 802 | Bits | 1 | Idle air control setup |
| Idle Air Control Average Maximum Value | 0x0332 | 818 | Value | 1 | Maximum value for idle air control moving average |
| Idle Air Control Average Minimum Value | 0x0333 | 819 | Value | 1 | Minimum value for idle air control moving average |
| Idle Air Control Moving Average Factor | 0x0336 | 822 | Value | 1 | Idle air control factor to set up moving average |
| Idle Air Control Average Maximum Engine Temperature | 0x0337 | 823 | Value | 1 | Maximum engine temperature for idle air control moving average |
| Idle Air Control Average Minimum Engine Temperature | 0x0338 | 824 | Value | 1 | Minimum engine temperature for idle air control moving average |
| Running IAC Position Map Engine Temp. Axis | 0x0339 | 825 | Axis | 4 | Running IAC Position Map Engine Temp. Axis |
| Running IAC Position Map Gear Axis | 0x033d | 829 | Axis | 3 | Running IAC Position Map Gear Axis |
| Running (Gear) IAC Position Map | 0x0340 | 832 | Map | 12 | IAC Position Map for running in gear |
| Running IAC Position Map RPM Axis | 0x034c | 844 | Axis | 4 | Running IAC Position Map RPM Axis |
| Running (RPM) IAC Position Map | 0x0350 | 848 | Map | 16 | IAC Position Map for running RPM |
| Idle Air Control Key-On Position | 0x0360 | 864 | Table | 8 | IAC position for startup |
| Idle Air Control Setpoint Table | 0x0368 | 872 | Table | 12 | Idle RPM setpoint table. |
| Idle Air Control Startup Correction | 0x0374 | 884 | Map | 4 | IAC RPM setpoint correction for startup |
| Idle Air Control Throttle Position Adjustment | 0x0378 | 888 | Table | 16 | Throttle position adjustment table for IAC position |
| CAN Bus Configuration | 0x0392 | 914 | Bits | 1 | CAN bus setup |
| Global Fuel Scale Increment | 0x0394 | 916 | Value | 1 | Incremental Fuel scale, time per unit of fuel |
| Cold Start Condition | 0x0399 | 921 | Value | 1 | Engine temperature indicates a cold engine condition. The CAN cold flag is set and cold engine RPM limit apply. |
| Aux Power Relay Configuration | 0x03b2 | 946 | Bits | 1 | Aux Power Relay Configuration |
| Aux Power Relay On Battery Voltage | 0x03b3 | 947 | Value | 1 | Battery voltage above which aux relay turned on |
| Aux Power Relay Off Battery Voltage | 0x03b4 | 948 | Value | 1 | Battery voltage below which aux relay turned off |
| Aux Power Relay Switching Delay | 0x03b5 | 949 | Value | 1 | Delay before switching aux relay |
| Spark Plug Cleaning Configuration | 0x03b6 | 950 | Bits | 1 | Spark Plug Cleaning Configuration |
| Spark Plug Cleaning Maximum Engine Temperature | 0x03b8 | 952 | Value | 1 | No plug cleaning needed if TE exceeds this |
| Spark Plug Cleaning Waste Fire Maximum Engine Temperature | 0x03b9 | 953 | Value | 1 | Terminate plug cleaning waste fires above this TE |
| Spark Plug Cleaning Engine Minimum Run Time | 0x03ba | 954 | Value | 1 | Min time for engine run event for plug cleaning |
| Spark Plug Cleaning Number of Cold Runs | 0x03bb | 955 | Value | 1 | Cold run events before plug cleaning needed |
| Spark Plug Key-On Cleaning Time | 0x03bd | 957 | Value | 1 | Duration of key-on plug cleaning |
| Spark Plug Cleaning Number of Waste Fires | 0x03be | 958 | Value | 1 | Plug cleaning waste fires per rev |
| Fuel Pressure Control Configuration | 0x03c2 | 962 | Bits | 1 | Fuel Pressure Control Configuration |
| Fuel Pressure Key-Off Minimum Pressure | 0x03d8 | 984 | Table | 6 | Minimum fuel pressure when engine off |
| Fuel Pressure Setpoint for Startup | 0x03e6 | 998 | Map | 4 | Fuel Pressure setpoint at startup |
| Fuel Pressure Setpoint for Engine Temperature | 0x03ea | 1002 | Table | 28 | Fuel pressure setpoint table for engine temperature |
| Fuel Pressure Sensor Conversion Table | 0x0406 | 1030 | Table | 28 | Fuel pressure sensor data |
| Fuel Pressure Setpoint Load Axis | 0x0422 | 1058 | Axis | 6 | Load axis for fuel pressure setpoint map |
| Fuel Pressure Setpoint RPM Axis | 0x0428 | 1064 | Axis | 12 | RPM axis for fuel pressure setpoint map |
| Fuel Pressure Setpoint | 0x0434 | 1076 | Map | 36 | Fuel pressure setpoint map for RPM and load |
| Voltage and Fuel Pressure Correction Temperature Axis | 0x0458 | 1112 | Axis | 6 | Fuel pressure axis for voltage and fuel pressure correction map |
| Voltage and Fuel Pressure Correction Battery Axis | 0x045e | 1118 | Axis | 12 | Battery axis for voltage and fuel pressure correction map |
| Voltage and Fuel Pressure Correction | 0x046a | 1130 | Map | 36 | Injector adder based on fuel pressure and battery |
| Fuel Pressure Correction | 0x048e | 1166 | Table | 8 | Fuel Pressure correction |
| Fuel Pulse Endpoint Load Axis | 0x0496 | 1174 | Axis | 6 | Fuel endpoint load axis |
| Fuel Pulse Endpoint RPM Axis | 0x049c | 1180 | Axis | 12 | Fuel endpoint RPM axis |
| Fuel Pulse Endpoint Table | 0x04a8 | 1192 | Map | 36 | Fuel endpoint speed/load table |
| Rides Required to Clear DTC | 0x04cc | 1228 | Value | 1 | Number of rides without error codes set to clear store errors |
| Throttle Position Sensor Number of Errors | 0x04cd | 1229 | Value | 1 | Number of TPS read failures before error code is set |
| Throttle Position Sensor Highest Reading Allowed | 0x04ce | 1230 | Value | 2 | Maximum TPS reading |
| Throttle Position Sensor Lowest Reading Allowed | 0x04d0 | 1232 | Value | 2 | Minimum TPS reading |
| Throttle Position Sensor Default Value | 0x04d2 | 1234 | Value | 2 | TPS default value set on failure |
| O2 Sensor Test Minimum RPM | 0x04d4 | 1236 | Value | 2 | Minimum RPM to check for O2 activity |
| O2 Sensor Test Minimum Throttle | 0x04d6 | 1238 | Value | 1 | Minimum throttle to check for O2 activity |
| O2 Sensor Number of Errors | 0x04d7 | 1239 | Value | 1 | Number of O2 sensor read failures before error code is set |
| O2 Sensor Number of Inactive Reads | 0x04d8 | 1240 | Value | 1 | Number of inactive results before error code is set |
| Engine Temperature Sensor Number of Errors | 0x04d9 | 1241 | Value | 1 | Number of ET sensor read failures before error code is set |
| Engine Temperature Sensor Highest Reading Allowed | 0x04da | 1242 | Value | 1 | Maximum ET sensor reading |
| Engine Temperature Sensor Lowest Reading Allowed | 0x04db | 1243 | Value | 1 | Minimum ET sensor reading |
| Engine Temperature Sensor Default Value | 0x04dc | 1244 | Value | 1 | ET sensor default value set on failure |
| Air Temperature Sensor Highest Reading Allowed | 0x04dd | 1245 | Value | 1 | Maximum allowed air temperature sensor reading |
| Air Temperature Sensor Lowest Reading Allowed | 0x04de | 1246 | Value | 1 | Minimum allowed air temperature sensor reading |
| Air Temperature Sensor Default Value | 0x04df | 1247 | Value | 1 | Air temperature sensor default value, set on failure |
| Air Temperature Sensor Number of Errors | 0x04e0 | 1248 | Value | 1 | Number of air temperature sensor test failures before error code is set |
| Battery Average Voltage Difference Limit | 0x04e5 | 1253 | Value | 1 | Maximum difference allowed between average high and low battery voltage |
| Battery Voltage Test Minimum RPM | 0x04e6 | 1254 | Value | 1 | Minimum engine speed to perform battery voltage tests |
| Battery Voltage Number of Errors | 0x04e7 | 1255 | Value | 1 | Number of battery voltage test failures before error code is set |
| Battery Voltage Highest Reading Allowed | 0x04e8 | 1256 | Value | 2 | Battery voltage maximum reading allowed |
| Battery Voltage Lowest Reading Allowed | 0x04ea | 1258 | Value | 2 | Battery voltage minimum reading allowed |
| Battery Voltage Default Value | 0x04ec | 1260 | Value | 2 | Battery voltage default value, set on failure |
| Active Muffler Controller Number of Tests Failed | 0x04ee | 1262 | Value | 1 | Number of AMC test failures before error code is set |
| Active Muffler Controller Max Feedback Time | 0x04ef | 1263 | Value | 1 | Maximum time allowed for AMC feedback |
| Active Intake Maximum TPS Reading Allowed | 0x04f0 | 1264 | Value | 1 | Maximum TPS reading while AIC is active |
| Active Intake Error Counts | 0x04f1 | 1265 | Value | 1 | Number of failed active intake tests before setting an error code |
| Active Intake Feedback Timeout | 0x04f2 | 1266 | Value | 1 | Active Intake Control feedback timeout |
| Injector Feedback Highest Reading Allowed | 0x04f3 | 1267 | Value | 1 | Maximum injector feedback reading |
| Injector Feedback Lowest Reading Allowed | 0x04f4 | 1268 | Value | 1 | Minimum injector feedback reading |
| Injector Feedback Number of Errors | 0x04f5 | 1269 | Value | 1 | Number of injector feedback test failures before error code is set |
| Coil Feedback Highest Reading Allowed | 0x04f6 | 1270 | Value | 1 | Maximum allowed coil feedback reading |
| Coil Feedback Lowest Reading Allowed | 0x04f7 | 1271 | Value | 1 | Minimum allowed coil feedback reading |
| Coil Feedback Number of Errors | 0x04f8 | 1272 | Value | 1 | Number of failed coil feedback tests before error code is set |
| Clutch Test Number of VSS Samples | 0x04f9 | 1273 | Value | 1 | Number of vehicle speed samples for clutch diagnostic tests |
| Clutch Test Minimum Load | 0x04fa | 1274 | Value | 1 | Minimum load to run clutch diagnostic tests |
| Clutch Test Timeout | 0x04fb | 1275 | Value | 1 | Number of failed clutch diagnostic tests before error code is set |
| Neutral Test Number of VSS Samples | 0x04fc | 1276 | Value | 1 | Number of vehicle speed samples for neutral diagnostic tests |
| Neutral Test Minimum Load | 0x04fd | 1277 | Value | 1 | Minimum load for neutral diagnostic |
| Neutral Test Timeout | 0x04fe | 1278 | Value | 1 | Neutral diagnostic timeout |
| Fuel Pump Feedback Upper Limit | 0x04ff | 1279 | Value | 1 | Maximum fuelpump feedback reading |
| Fuel Pump Feedback Off Time before Test | 0x0500 | 1280 | Value | 1 | Off time before fuel pump feedback checked |
| Fuel Pump Feedback Number of Errors | 0x0501 | 1281 | Value | 1 | Number of fuelpump feedback test failures before error code is set |
| Idle Air Control Position Test Maximum Engine Temperature | 0x0505 | 1285 | Value | 1 | Maximum engine temperature to test idle air control position |
| Idle Air Control Position Test Limit High | 0x0506 | 1286 | Value | 1 | IAC position high diagnostic limit 255 disables) |
| Idle Air Control Position Test Limit Low | 0x0507 | 1287 | Value | 1 | IAC position low diagnostic limit |
| Idle Air Control Highest Reading Allowed | 0x0508 | 1288 | Value | 1 | IAC high position limit |
| Idle Air Control Lowest Reading Allowed | 0x0509 | 1289 | Value | 1 | IAC low position limit |
| Idle Air Control Position Test Timeout | 0x050a | 1290 | Value | 1 | Idle air control position diagnostic timeout |
| Idle Air Control Test Timeout | 0x050b | 1291 | Value | 1 | IAC diagnostic timeout |
| Tacho Feedback Number of Errors | 0x050c | 1292 | Value | 1 | Number of tacho feedback test failures before error code is set |
| Fan Feedback Off Time before Test | 0x050d | 1293 | Value | 1 | Fan off-time before running feedback test |
| Fan Feedback Number of Errors | 0x050e | 1294 | Value | 1 | Number of failed fan tests before error code is set |
| VSS Input Test Timeout | 0x0512 | 1298 | Value | 1 | Vehicle Speed Input diagnostic timeout |
| Bank Angle Sensor Highest Reading Allowed | 0x0515 | 1301 | Value | 1 | Maximum bank angle sensor reading allowed (alternative: shifter configuration) |
| Bank Angle Sensor Tip-Over Value | 0x0516 | 1302 | Value | 1 | Bank angle sensor tip-over value (alternative: shifter minimum delay between activations) |
| Bank Angle Sensor Lowest Reading Allowed | 0x0517 | 1303 | Value | 1 | Minimum bank angles sensor reading allowed (alternative: shifter debounce period) |
| Bank Angle Sensor Number of Errors | 0x0518 | 1304 | Value | 1 | Number of bank angle sensor test failures before error code is set (alternative: shifter fuel cut duration) |
| Bank Angle Sensor Tipover Delay | 0x0519 | 1305 | Value | 1 | Bank angle sensor tip-over detection delay (alternative: shifter maximum input activation value) |
| Starter Relay Test Timeout | 0x051a | 1306 | Value | 1 | Starter Relay diagnostic timeout |
| Aux Power Relay Test Feedback Timeout | 0x051b | 1307 | Value | 1 | Auxiliary Power Relay diagnostic timeout |
| EEPROM Test Number of Errors | 0x051c | 1308 | Value | 1 | Number of failed EEPROM checksum tests before error code set |
| AD-Converter Number of Errors | 0x051d | 1309 | Value | 1 | Number of failed A/D conversion tests before error code set |
| Camshaft Sensor Test Minimum RPM | 0x051e | 1310 | Value | 2 | Minimum RPM to set lost sync error |
| Camshaft Sensor Number of Sync Errors | 0x0520 | 1312 | Value | 1 | Number of revs without sync detected before error code set |
| Camshaft Sensor Test Number of Consecutive Sync Errors | 0x0521 | 1313 | Value | 1 | Number of consecutive out-of-sync revs before error code set |
| AFV Cylinder Difference Limit | 0x0525 | 1317 | Value | 1 | Learned Fuel Cylinder Difference limit |
| AFV Cylinder Difference Number of Errors | 0x0526 | 1318 | Value | 1 | Learned Fuel Cylinder Difference timeout |
| MAP Sensor Highest Reading Allowed | 0x0527 | 1319 | Value | 1 | Highest MAP sensor reading allowed |
| MAP Sensor Lowest Reading Allowed | 0x0528 | 1320 | Value | 1 | Lowest MAP sensor reading allowed |
| MAP Sensor Default Value | 0x0529 | 1321 | Value | 1 | Default MAP value set on failure |
| Map Sensor Number of Errors | 0x052a | 1322 | Value | 1 | Number of MAP sensor read failures before error code is set |
| Barometric Pressure Sensor Highest Reading Allowed | 0x052b | 1323 | Value | 1 | Barometric pressure sensor maximum reading allowed |
| Barometric Pressure Sensor Lowest Reading Allowed | 0x052c | 1324 | Value | 1 | Barometric pressure sensor mininmum reading allowed |
| Barometric Pressure Sensor Default Value | 0x052d | 1325 | Value | 1 | Barometric pressure sensor default value, set on failure |
| Barometric Pressure Sensor Number of Errors | 0x052e | 1326 | Value | 1 | Number of barometric pressure sensor test failures before error code is set |
| Error Mask Byte 0 | 0x0539 | 1337 | Bits | 1 | Diagnostic trouble code mask, byte 0 |
| Error Mask Byte 1 | 0x053a | 1338 | Bits | 1 | Diagnostic trouble code mask, byte 1 |
| Error Mask Byte 2 | 0x053b | 1339 | Bits | 1 | Diagnostic trouble code mask, byte 2 |
| Error Mask Byte 3 | 0x053c | 1340 | Bits | 1 | Diagnostic trouble code mask, byte 3 |
| Error Mask Byte 4 | 0x053d | 1341 | Bits | 1 | Diagnostic trouble code mask, byte 4 |
| Error Mask Byte 5 | 0x053e | 1342 | Bits | 1 | Diagnostic trouble code mask, byte 5 |
| Error Mask Byte 6 | 0x053f | 1343 | Bits | 1 | Diagnostic trouble code mask, byte 6 |
| Error Mask Byte 7 | 0x0540 | 1344 | Bits | 1 | Diagnostic trouble code mask, byte 7 |
| Error Mask Byte 8 | 0x0541 | 1345 | Bits | 1 | Diagnostic trouble code mask, byte 8 |
| Error Mask Byte 9 | 0x0542 | 1346 | Bits | 1 | Diagnostic trouble code mask, byte 9 |
| Error Mask Byte 10 | 0x0543 | 1347 | Bits | 1 | Diagnostic trouble code mask, byte 10 |
| Dwell Duration | 0x0545 | 1349 | Array | 17 | Dwell duration table |
| Timing Table Load Axis | 0x0556 | 1366 | Axis | 10 | Timing table load axis y-axis) |
| Timing Table RPM Axis | 0x0560 | 1376 | Axis | 28 | Timing table RPM axis x-axis) |
| Fuel Map Load Axis | 0x057c | 1404 | Axis | 16 | Fuel load axis |
| Fuel Map RPM Axis | 0x058c | 1420 | Axis | 40 | Fuel RPM axis |
| 2nd Fuel Map Load Axis | 0x05b4 | 1460 | Axis | 8 | Secondary injector load axis |
| 2nd Fuel Map RPM Axis | 0x05bc | 1468 | Axis | 24 | Secondary injector RPM axis |
| Timing Table Front | 0x05d4 | 1492 | Map | 140 | Timing table front cylinder |
| Timing Table Rear | 0x0660 | 1632 | Map | 140 | Timing table rear cylinder |
| Fuel Map Front | 0x0718 | 1816 | Map | 320 | Front fuel table |
| Fuel Map Rear | 0x0858 | 2136 | Map | 320 | Fuel map rear cylinder |
| 2nd Fuel Map Front | 0x0998 | 2456 | Map | 96 | Front showerhead table |
| 2nd Fuel Map Rear | 0x09f8 | 2552 | Map | 96 | Rear showerhead table |
| Air Temperature Maximum Spark Advance Reduction | 0x0a58 | 2648 | Map | 140 | Maximum TA spark retard |
| TP to Load Table TP Axis | 0x0ae4 | 2788 | Axis | 8 | Throttle position axis for TP to load conversion map |
| TP to Load Table RPM Axis | 0x0aec | 2796 | Axis | 16 | RPM axis for TP to load conversion map |
| TP to Load Table | 0x0afc | 2812 | Map | 64 | Throttle position to load conversion map |
| MAP to Load Table MAP Axis | 0x0b3c | 2876 | Axis | 8 | MAP axis for MAP to load conversion map |
| MAP to Load Table RPM Axis | 0x0b44 | 2884 | Axis | 16 | RPM axis for MAP to load conversion map |
| MAP to Load Table Front | 0x0b54 | 2900 | Map | 64 | Convert front MAP to load |
| MAP to Load Table Rear | 0x0b94 | 2964 | Map | 64 | Convert rear MAP to load |
| TP to Load Weight Table TP Axis | 0x0bd4 | 3028 | Axis | 8 | Throttle position axis for TP to load weight map |
| TP to Load Weight Table RPM Axis | 0x0bdc | 3036 | Axis | 16 | RPM axis for TP to load weight map |
| TP to Load Weight Table | 0x0bec | 3052 | Map | 64 | Weight of TPS vs MAP) in load calculation |
Note:
For variables that have a scaling factor and/or a translational offset given, use this formula to calculate the output value:
output_value = (EEPROM_value * scale) + translate
Please double-check all information from this site before using them!